DEMO KIT AVAILABLE
19-5754; Rev 3/11
DS26324
3.3V, 16-Channel, E1/T1/J1 Short-Haul Line Interface Unit
GENERAL DESCRIPTION
FEATURES
.
16 E1, T1, or J1 Short-Haul Line Interface
Units
The DS26324 is a 16-channel short-haul line
interface unit (LIU) that supports E1/T1/J1 from a
single 3.3V power supply. A wide variety of
applications are supported through internal
impedance matching. A single bill of material can
support E1/T1/J1 that requires no external
termination. Redundancy is supported through
nonintrusive monitoring, optimal high-impedance
modes and configurable 1:1 or 1+1 backup
enhancements. An on-chip synthesizer generates the
E1/T1/J1 clock rates by a single master clock input of
various frequencies. Two clock output references are
also offered. The device is offered in a 256-pin
TE-CSBGA, the smallest package available for a
16-channel LIU.
.
.
Independent E1, T1 or J1 Selections
Fully Internal Impedance Match Requires No
External Resistors
.
Software-Selectable Transmit and Receive-
Side Impedance Match
.
.
Crystal-Less Jitter Attenuator
Selectable Single-Rail and Dual-Rail Mode
and AMI or HDB3/B8ZS Line Encoding and
Decoding
.
.
Detection and Generation of AIS
Digital/Analog Loss of Signal Detection as
per T1.231, G.775 and ETS 300 233
APPLICATIONS
T1 Digital Cross-Connects
ATM and Frame Relay Equipment
Wireless Base Stations
.
External Master Clock Can Be Multiple of
2.048MHz or 1.544MHz for T1/J1 or E1
Operation; This Clock Will Be Internally
Adapted for T1 or E1 Usage
ISDN Primary Rate Interface
E1/T1/J1 Multiplexer and Channel Banks
E1/T1/J1 LAN/WAN Routers
.
Receiver Signal Level Indicator from -2.5dB to
-20dB in 2.5dB Increments
.
.
Two Built-In BERT Testers for Diagnostics
FUNCTIONAL DIAGRAM
8-Bit Parallel Interface Support for Intel or
Motorola Mode or a 4-Wire Serial Interface
.
.
.
Transmit Short-Circuit Protection
G.772 Nonintrusive Monitoring
JTAG
SOFTWARE CONTROL
AND JTAG
Receive Monitor Mode Handles Combinations
of 14dB to 20dB of Resistive Attenuation
Along with 12dB to 30dB of Cable Attenuation
LOSS
RTIP
RPOS
RNEG
RCLK
.
Specification Compliance to the Latest T1
and E1 Standards
RECEIVER
RRING
TPOS
TTIP
.
.
Single 3.3V Supply with 5V Tolerant I/O
JTAG Boundary Scan as Per IEEE 1149.1
TNEG
TCLK
TRANSMITTER
TRING
1
ORDERING INFORMATION
PART
TEMP RANGE PIN-PACKAGE
DS26324G+
0°C to +70°C 256 TE-CSBGA
16
DS26324GN+ -40°C to +85°C 256 TE-CSBGA
DS26324G
DS26324GN
0°C to +70°C 256 TE-CSBGA
-40°C to +85°C 256 TE-CSBGA
+Denotes a lead(Pb)-free/RoHS compliant package.
Note: Some revisions of this device may incorporate deviations from published specifications known as errata. Multiple revisions of any device
may be simultaneously available through various sales channels. For information about device errata, click here: www.maxim-ic.com/errata.
1 of 120