InstallationDISN RhaileMeoutnt
PART NUMBER NOMENCLATURE
Rated Load Current
20: 20 Amps
Switching Type
30: 30 Amps
Blank: Zero Voltage Turn-On
R: Instantaneous Turn-On
(AC Output only)
Operating Voltage
20: 1-200 VDC
60: 48-600 VAC
35: 35 Amps [High I2t]
(AC Output only)
DR22 Series Solid State Relays
Series
Crydom DR22 Series Solid State Relays were developed to offer the advantages of
semiconductor switching technology in a standard 22.5 mm industrial package. Quick and easy
installation is coupled with low drive power requirements and efficient, reliable power SCR
output. This compact new design offers up to 35 ARMS in ambient temperatures of 40ºC.
DR22
60
A
20
UV
R
J
Control Voltage
Terminal Layout
Input Connector
A: 90-280 VAC/VDC
(AC Output only)
D: 4-32 VDC
U: Relay Configuration
V: Contactor
Blank: Screw Terminal
J: Spring Terminal
(V and W suffixes only)
Be sure to visit the product series datasheet available at the Crydom website to complement this
information. If you have questions or need additional information please contact Crydom Tech
Support.
Configuration
AC
Output
only
(std. screw)
W: Contactor
Configuration
(elevator screw)
Please read all instructions before using your DIN Rail Mount Solid State Relay (SSR).
Required for valid part number
For options only and not required for valid part number
MOUNTING INSTRUCTIONS
Install the relay on the DIN Rail (as shown in fig. 1)
To install
on DIN rail
■
WIRING DIAGRAMS
■
Maximum recommended terminal screw torque input
terminal:
Relay AC
Contactor AC
Relay DC (A)
To remove
from DIN rail
(-
/
)
(
-
)
(+ /
)
(+)
♦Contactor configuration (”V” & “W” suffixes):
5 in-lb (0.5 Nm)
V
AC
♦Relay configuration (”U” suffix):
13-15 in-lb (1.5-1.7 Nm)
1/L1
+3/A1
-4/A2
+3/A1
-4/A2
■
Maximum recommended terminal screw torque load
fig. 1 SSR mounted on DIN rail
(-/ )
)
(+ /
terminal:
INPUT
STATUS
INPUT
STATUS
♦Contactor configuration (”V” & “W” suffixes): 18-20 in-lb (2.0-2.2 Nm)
♦Relay configuration (”U” suffix): 13-15 in-lb (1.5-1.7 Nm)
INPUT
STATUS
+3/A1 -4/A2
Load
■
■
If multiple units are installed be sure to follow derating curves
Recommended wire sizes as shown in TABLE 1
WARNING! Removing product from 35 mm rail incorrectly by not using the appropriate tool
1/L1
2/T1
+1
-2
would damage the latching system.
2/T1
+
AC
V
TABLE 1. Recommended Wire Sizes
+
V
-
Load
(B)
Load
Terminal
Configuration
Wire Size
(Solid / Stranded)
Wire Pull-Out
Strength (lb)[N]*
2
2 x 18 AWG (1 mm ) Stranded [minimum]
20 [88]
60 [266]
20 [88]
40 [177]
25 [111]
80 [355]
90 [400]
4.5 [20]
30 [133]
5 [22]
Output
Relay “U” suffix
■
Important Considerations
♦Be sure to use input and output voltages within
2
2 x 10 AWG (6 mm ) Stranded [maximum]
0.89 in [22.5 mm]
Minimum
2
operating ranges.
2 x 18 AWG (1 mm ) Stranded
Input
Relay “U” suffix
♦LED indicates only input status. It does not
represent output status.
♦To achieve maximum ratings, there must be a
minimum spacing of 0.89 in (22.5 mm) between the
devices in free air (as shown in fig.2).
2
2 x 12 AWG (4 mm ) Stranded
2
Output
Contactor
“V” &“W”
suffixes
2 x 20 AWG (0.75 mm ) [minimum]
2
2 x 10 AWG (6 mm )
2
2 x 8 AWG (10 mm ) [maximum]
♦Protective Earth (PE) screw type recommended is
10-32 UNC standard, not provided with SSR. Through
the use of a DIN rail ground (protective conductor)
terminal block, the DIN rail itself can be used as the
grounding bus bar. In this case, the zinc plated steel
material used for the DIN rail clip of DR22 models,
permits a secure path to ground and avoid the need of
a further PE connection (see fig.3).
2
30 AWG (0.05 mm ) [minimum]
Input
Screw
Spring
2
12 AWG (3.3 mm ) [maximum]
Contactor
“V” &“W”
suffixes
fig. 2 Multiple units
mounting
for maximum
ratings
2
26 AWG (0.13 mm ) [minimum]
fig. 3 DR22 model
with Protective
Earth screw
2
12 AWG (3.3 mm ) [maximum]
5 [22]
* Tests performed on Stranded wire
TABLE 3. Recommended Accessories
TABLE 2. Compatible Terminals
W
D
W D
Terminals
Fork Lug
Ring Lug
Copper Lug
Copper Lug
Connectors
ID Marker
Lug Terminal
Crydom Part No.
TRM0
TRM6
CP201
CP202
CNLB
CNLN
CNL2
TRM0
TRM6
Width [W] in (mm)
Stud Size Dia [D] (in)
Wire Size AWG
0.45 (11.4)
#8 (0.168)
0.45 (11.4)
#8 (0.168)
6-0
14-6
General Notes
(A) Load can be wired to either terminal 1 or terminal 2. Proper polarity must be observed for the DC control power supply, with terminal 3 being positive with respect to terminal 4.
(B) DC inductive loads must be diode suppressed.
(C) AC input models operating range is -20 to 60 ºC
Rev. 060816
Do not forget to visit us at: www.crydom.com
Copyright © 2016 Crydom Inc. Specifications subject to change without notice.
5秒后页面跳转
英伟达新AI芯片Rubin或提前半年亮相
苹果iPhone 17将全系采用三星/LG显示LTPO OLED面板
三星深化印度制造布局，供应链本地化进程加速
芯擎科技“星辰一号”自动驾驶芯片点亮成功，2025年量产在即
微信公众号
抖音公众号
浙公网安备 33010502006866号 浙ICP备10014259号-119
营业执照ICP证
数据手册
如果您发现信息不准确，
