DPA423-426
™
DPA-Switch Family
Highly Integrated DC-DC Converter ICs
for Distributed Power Architectures
Product Highlights
V
O
Highly Integrated Solution
• Eliminates 20-50 external components–saves space, cost
• Integrates 220 V high frequency MOSFET, PWM control
• Lower cost plastic DIP surface mount (G package) and
SENSE
CIRCUIT
DPA-Switch
V
IN
D
L
through-hole (P package) options for designs ≤35 W
CONTROL
RESET/
CLAMP
CIRCUIT
C
Superior Performance and Flexibility
• Eliminates all external current sensing circuitry
• Built-inauto-restartforoutputoverload/openloopprotection
• Pin selectable 300/400 kHz fixed frequency
S
X
F
PI-2770-032002
• Wide input (line) voltage range: 16-75 VDC
• Source connected tab reduces EMI
Figure 1. Typical Forward Converter Application.
• Line under-voltage (UV) detection: meets ETSI standards
• Line overvoltage (OV) shutdown protection
• Low cost synchronous rectification: line UV/OV shut down
limits gate drive voltage range from transformer winding
• Fully integrated soft-start for minimum stress/overshoot
• Externally programmable current limit
• Supports forward or flyback topology
• Cycle skipping: regulation to zero load without pre-load
• Hysteretic thermal shutdown for automatic fault recovery
OUTPUT POWER TABLE
36-75 VDC INPUT RANGE (FORWARD)2,4
Total Device
Max
0.5 W 1 W 2.5 W 4 W 6 W Power
Output1
Dissipation3
PRODUCT4
DPA423
12 W 16 W
-
-
-
-
-
-
18 W
35 W
70 W
16 W 23 W 35 W
DPA424
EcoSmart®- Energy Efficient
• Extremely low consumption at no load
DPA425
23 W 32 W 50 W 62 W
25 W 35 W 55 W 70 W 83 W 100 W
36-75 VDC INPUT RANGE (FLYBACK)2
DPA426
• Cycle skipping at light load for high standby efficiency
Total Device3
Max
1.5 W Power
Output1
Applications
Dissipation
PRODUCT4
DPA423
0.5 W 0.75 W 1 W
• Telco central office equipment: xDSL, ISDN, PABX, etc.
• Distributed power architectures (24 V/48 V bus, etc.)
• Digital feature phones, VoIP phones, PoE
• Industrial controls (24 V/48 V)
9 W
13 W
-
-
13 W
10 W 14.5 W 18 W 24 W 26 W
DPA424
5
5
5
DPA425
-
-
-
25.5 W 52 W
Description
Table 1. Notes: 1. Maximum output power is limited by device internal
current limit. 2. See Applications Considerations section for complete
description of assumptions and for output powers with other input voltage
ranges. 3. For device dissipation of 1.5 W or below, use Por G packages.
Device dissipation above 1.5 W is possible only with R package. 4. See
Part Ordering Information. 5. Due to higher switching losses, the DPA425
may not deliver additional power compared to a smaller device.
The DPA-Switch IC family introduces a highly integrated
solution for DC-DC conversion applications in the 16-75 VDC
input range.
DPA-Switch uses the same proven topology as TOPSwitch, cost
effectively integrating the high voltage power MOSFET, PWM
control, fault protection and other control circuitry onto a single
CMOS chip. High performance features are enabled with three
user configurable pins.
The following transparent or built-in features are also provided:
soft-start, cycle skipping down to zero load and hysteretic
thermal shutdown. In addition, all critical parameters (i.e.
current limit, frequency, PWM gain) have tight temperature
and absolute tolerance, to simplify design and optimize system
cost.
January 2004