Series
D100
Single & Dual Output
Miniature, 1W SIP
DC/DC Converters
Electrical Specifications
Specifications typical @ +25°C, nominal input voltage & rated output current, unless otherwise noted. Specifications subject to change without notice.
Input
Parameter
Key Features:
• 1W Output Power
Conditions
Min.
Typ.
5.0
Max.
5.5
Units
5 VDC Input
4.5
• Miniature SIP Case
• Single & Dual Outputs
• Complies to RFI Standards
12 VDC Input 10.8
24 VDC Input 21.6
48 VDC Input 43.2
Internal Capacitor
12.0
24.0
48.0
13.2
26.4
52.8
Input Voltage Range
VDC
• 1,000 VDC Isolation
• >1.12 MHour MTBF
• 36 Standard Models
• Industry Standard Pin-Out
Input Filter
Reflected Ripple Current
12 μH Source Inductance
20
mA P - P
Output
Parameter
Output Voltage Accuracy
Output Voltage Balance
Line Regulation
Conditions
Min.
Typ.
3.0
1.0
1.2
Max.
Units
%
Dual Output , Balanced Loads
For Vin Change of 1%
%
%
Load Regulation (Note 1)
Ripple & Noise (20 MHz) (Note 2)
Output Power Protection
Temperature Coefficient
Output Short Circuit
General
See Model Selection Guide
75
mV P - P
%
110
0.02
%/ºC
Momentary (0.5 Sec.)
RoHS Compliant
Parameter
Conditions
Min.
60 Seconds 1,000
500 VDC 1,000
100 kHz, 1V
Typ.
Max.
Units
VDC
MΩ
pF
Isolation Voltage
Isolation Resistance
Isolation Capacitance
Switching Frequency
EMI/RFI
60
80
kHz
EN55022 B, EN55024 B, IEC 61000-4-2, IEC 61000-4-3, FCC 47 CFR Part 15 B
Environmental
Parameter
Conditions
Min.
Typ.
Max.
+85
Units
ºC
Operating Temperature Range
Operating Temperature Range
Storage Temperature Range
Cooling
Ambient
Case
-40
+25
+100
+125
ºC
-40
ºC
Free Air Convection
RH, Non-condensing
Humidity
95
%
Physical
MicroPower Direct
292 Page Street
Suite D
Stoughton, MA 02072
USA
Case Size (5V 12V & 24V Input Models)
Case Size (48V Input Models)
Case Material
0.76 x 0.24 x 0.39 Inches (19.5 x 6.0 x 10.0 mm)
0.76 x 0.28 x 0.39 Inches (19.5 x 7.2 x 10.0 mm)
Non-Conductive Black Plastic (UL94-V0)
0.08 Oz (2.3g)
Weight
Reliability Specifications
Parameter
MTBF
T: (781) 344-8226
F: (781) 344-8481
E: sales@micropowerdirect.com
W: www.micropowerdirect.com
Conditions
Min.
Typ.
Typ.
Max.
Units
MIL HDBK 217F, 25ºC, Gnd Benign 1.12
MHours
Absolute Maximum Ratings
Parameter
Conditions
Min.
Max.
7.0
Units
5 VDC Input -0.7
12 VDC Input -0.7
24 VDC Input -0.7
48 VDC Input -0.7
15.0
28.0
54.0
260
Input Voltage Surge (1 Sec)
VDC
Lead Temperature
1.5 mm From Case For 10 Sec
All Models
ºC
Internal Power Dissipation
450
mW
Caution: Exceeding Absolute Maximum Ratings may damage the module. These are not continuous operating ratings.