CY8C95xx Preliminary Data Sheet
Overview
Document Conventions
Table of Contents
The following is a table of contents for the remainder of this data
sheet.
Acronyms
2.
Pinouts and Pin Descriptions ..................................................5
2.1 Pinouts ..............................................................................5
2.1.1 28-Pin Part Pinout ................................................5
2.1.2 48-Pin Part Pinout ................................................6
2.1.3 100-Pin Part Pinout ..............................................7
2.2 PIN Descriptions ................................................................9
2.2.1 Extendable Soft Addressing™ .............................9
2.2.2 Interrupt Pin (INT) .................................................9
2.2.3 Write Disable Pin (WD) ........................................9
2.2.4 External Reset Pin (XRES) ..................................9
2.2.5 Working with PWMs .............................................9
The following table lists the acronyms that are used in this doc-
ument.
Acronym
AC
Description
alternating current
direct current
DC
electrically erasable programmable read-only memory (E2)
general purpose IO
EEPROM
GPIO
I/O
input/output
3.
Register Reference .................................................................11
3.1 Register Mapping Table ..................................................11
3.2 Register Descriptions ......................................................12
3.2.1 Input Port Registers (00h - 07h) .........................12
3.2.2 Output Port Registers (08h - 0Fh) ......................12
3.2.3 Int. Status Port Registers (10h - 17h) .................12
3.2.4 Port Select Register (18h) ..................................12
3.2.5 Interrupt Mask Port Register (19h) .....................12
3.2.6 Select PWM Register (1Ah) ...............................12
3.2.7 Inversion Register (1Bh) .....................................12
3.2.8 Port Direction Register (1Ch) .............................12
3.2.9 Drive Mode Registers (1Dh-23h) ........................13
3.2.10 PWM Select Register (28h) ................................13
3.2.11 Config (29h) ........................................................13
3.2.12 Period Register (2Ah) .........................................13
3.2.13 Pulse Width Register (2Bh) ................................13
3.2.14 Divider Register (2Ch) ........................................13
3.2.15 Enable Register (2Dh) ........................................13
3.2.16 Device ID/Status Register (2Eh) ........................14
3.2.17 Command Register (30h) ...................................14
3.3 Commands Description ...................................................14
3.3.1 Store Config to E2 POR Defaults Cmd (01h) .....14
3.3.2 Restore Factory Defaults Cmd (02h) ..................14
3.3.3 Write E2 POR Defaults Cmd (03h) .....................14
3.3.4 Read E2 POR Defaults Cmd (04h) ....................15
3.3.5 Write Device Config Cmd (05h) ..........................15
3.3.6 Read Device Config Cmd (06h) .........................15
3.3.7 Reconfigure Device Cmd (07h) ..........................15
MSb
most-significant bit
POR
PWM
power on reset
pulse width modulator
Units of Measure
A units of measure table is located in the Electrical Specifica-
tions section. Table 4-1, “Units of Measure,” on page 16 lists all
the abbreviations used in Section 4.
Numeric Naming
Hexidecimal numbers are represented with all letters in upper-
case with an appended lowercase ‘h’ (for example, ‘14h’ or
‘3Ah’). Hexidecimal numbers may also be represented by a ‘0x’
prefix, the C coding convention. Binary numbers have an ap-
pended lowercase ‘b’ (e.g., 01010100b’ or ‘01000011b’). Num-
bers not indicated by an ‘h’, ‘b’, or 0x are decimal.
4.
Electrical Specifications .........................................................16
4.1 Absolute Maximum Ratings .............................................16
4.2 Operating Temperature ...................................................17
4.3 DC Electrical Characteristics ...........................................17
4.3.1 DC Chip-Level Specifications .............................17
4.3.2 DC Programming Specifications ........................18
4.3.3 DC General Purpose I/O Specifications .............18
4.4 AC Electrical Characteristics ...........................................19
4.4.1 AC General Purpose I/O Specifications .............19
4.4.2 AC PWM Output Jitter Specifications .................19
4.4.3 AC I2C Specifications .........................................20
5.
Packaging Information ...........................................................21
5.1 Packaging Dimensions ....................................................21
5.2 Thermal Impedances .......................................................23
5.3 Solder Reflow Peak Temperature ...................................23
6.
7.
Ordering Information ..............................................................24
6.1 Ordering Code Definitions ...............................................24
Sales and Service Information ...............................................25
7.1 Revision History ..............................................................25
7.2 Copyrights and Code Protection .....................................25
August 17, 2005
Document No. 38-12036 Rev. *A
4
5秒后页面跳转
STM32H743技术深度剖析与应用案例探索
LM321中文资料解析：引脚功能介绍、技术特点、技术特性分析
74HC14芯片资料介绍：性能特性分析、引脚介绍
LM1875芯片手册：功放参数分析、引脚说明、电路设计要点
微信公众号
抖音公众号
浙公网安备 33010502006866号 浙ICP备10014259号-119
营业执照ICP证
技术参数
数据手册
如果您发现信息不准确，
