CY8C9520A, CY8C9540A
CY8C9560A
20-, 40-, and 60-Bit IO Expander with
EEPROM
Features
Overview
■ I2C™ interface logic electrically compatible with SMBus
The CY8C95xxA is a multi-port IO expander with on board user
available EEPROM and several PWM outputs. All devices in this
family operate identically but differ in IO pins, number of PWMs,
■ Up to 20 (CY8C9520A), 40 (CY8C9540A), or 60 (CY8C9560A)
IO data pins independently configurable as inputs, outputs,
bi-directional input/outputs, or PWM outputs
and internal EEPROM size.
The CY8C95xxA operates as two I2C slave devices. The first
device is a multi port IO expander (single I2C address to access
all ports through registers). The second device is a serial
EEPROM. Dedicated configuration registers can be used to
disable the EEPROM. The EEPROM uses 2-byte addressing to
support the 28 Kbyte EEPROM address space. The selected
device is defined by the most significant bits of the I2C address
or by specific register addressing.
■ 4/8/16 PWM sources with 8-bit resolution
■ Extendable Soft Addressing™ algorithm allowing flexible
I2C-address configuration
■ Internal 3-/11-/27-Kbyte EEPROM
■ User default storage, IO port settings in internal EEPROM
■ Optional EEPROM Write Disable (WD) input
The IO expander's data pins can be independently assigned as
inputs, outputs, quasi-bidirectional input/outputs or PWM ouputs.
The individual data pins can be configured as open drain or
collector, strong drive (10 mA source, 25 mA sink), resistively
pulled up or down, or high impedance. The factory default config-
uration is pulled up internally.
■ Interrupt output indicates input pin level changes and Pulse
Width Modulator (PWM) state changes
■ Internal Power On Reset (POR)
■ Internal configurable Watchdog timer
The system master writes to the IO configuration registers
through the I2C bus. Configuration and output register settings
are storable as user defaults in a dedicated section of the
EEPROM. If user defaults were stored in EEPROM, they are
restored to the ports at power up. While this device can share the
bus with SMBus devices, it can only communicate with I2C
masters.
Top Level Block Diagram
WD
EEPROM
User
Settings
Area
User
Available
Area
There is one dedicated pin that is configured as an interrupt
output (INT) and can be connected to the interrupt logic of the
system master. This signal can inform the system master that
there is incoming data on its ports or that the PWM output state
was changed.
Clocks
32 kHz
24 MHz
GPort 0
GPort 1
GPort 2
GPort 3
8 Bit IO
5 Bit IO
The EEPROM is byte readable and supports byte-by-byte
writing. A pin can be configured as an EEPROM Write Disable
(WD) input that blocks write operations when set high. The
configuration registers can also disable EEPROM operations.
1.5 MHz
3 Bit IO
or A4-A6
93.75 kHz
4 Bit IO
or A1-A3, WD6
The CY8C95xxA has one fixed address pin (A0) and up to six
additional pins (A1-A6), which allow up to 128 devices to share
a common two wire I2C data bus. The Extendable Soft
Addressing algorithm provides the option to choose the number
of pins needed to assign the desired address. Pins not used for
address bits are available as GPIO pins.
Divider (1-255)
Control
Unit
PWM 0
8 Bit IO
8 Bit IO
PWM 15
GPort 7
There are 4 (CY8C9520A), 8 (CY8C9540A), or 16 (CY8C9560A)
independently configurable 8-bit PWMs. These PWMs are listed
as PWM0-PWM15. Each PWM can be clocked by one of six
available clock sources.
SCL
SDA
INT
A0
Vdd
Vss
Power-on-Reset
For details on how to configure I2C, see Application Note
"Communication - I2C Port Expander with Flash Storage -
AN2304" at http://www.cypress.com/design/2304.
Cypress Semiconductor Corporation
Document Number: 38-12036 Rev. *B
•
198 Champion Court
•
San Jose, CA 95134-1709
•
408-943-2600
Revised August 03, 2007
[+] Feedback
5秒后页面跳转
全球首块英伟达H200交付 黄仁勋“送货上门”
常用8脚开关电源芯片型号大全
74HC04芯片引脚图及功能、应用电路图讲解
CR6842芯片参数、引脚配置、应用电路图详解
微信公众号
抖音公众号
浙公网安备 33010502006866号 浙ICP备10014259号-119
营业执照ICP证
数据手册
如果您发现信息不准确，
