PSoC® 5LP: CY8C56LP Family
Datasheet
Programmable System-on-Chip (PSoC®)
General Description
With its unique array of configurable blocks, PSoC® 5LP is a true system level solution providing MCU, memory, analog, and digital
peripheral functions in a single chip. The CY8C56LP family offers a modern method of signal acquisition, signal processing, and
control with high accuracy, high bandwidth, and high flexibility. Analog capability spans the range from thermocouples (near DC
voltages) to ultrasonic signals. The CY8C56LP family can handle dozens of data acquisition channels and analog inputs on every
general-purpose input/output (GPIO) pin. The CY8C56LP family is also a high performance configurable digital system with some
part numbers including interfaces such as USB, multimaster inter-integrated circuit (I2C), and controller area network (CAN). In
addition to communication interfaces, the CY8C56LP family has an easy to configure logic array, flexible routing to all I/O pins, and
a high performance 32-bit ARM® Cortex™-M3 microprocessor core. You can easily create system level designs using a rich library
of prebuilt components and boolean primitives using PSoC Creator™, a hierarchical schematic design entry tool. The CY8C56LP
family provides unparalleled opportunities for analog and digital bill of materials integration while easily accommodating last minute
design changes through simple firmware updates.
Library of standard peripherals
• 8-, 16-, 24-, and 32-bit timers, counters, and PWMs
Features
32-bit ARM Cortex-M3 CPU core
• Serial peripheral interface (SPI), universal asynchronous
DC to 67 MHz operation
Flash program memory, up to 256 KB, 100,000 write cycles,
20 year retention, and multiple security features
Up to 32-KB flash error correcting code (ECC) or
configuration storage
Up to 64 KB SRAM
transmitter receiver (UART), I2C
• Many others available in catalog
Library of advanced peripherals
• Cyclic redundancy check (CRC)
• Pseudo random sequence (PRS) generator
• LIN bus 2.0
2-KB electrically erasable programmable read-only memory
(EEPROM) memory, 1 M cycles, and 20 years retention
• Quadrature decoder
Analog peripherals (1.71 V ≤ VDDA ≤ 5.5 V)
24-channel direct memory access (DMA) with multilayer
AHB[1] bus access
1.024 V±0.1% internal voltage reference across –40 °C to
+85 °C
• Programmable chained descriptors and priorities
• High bandwidth 32-bit transfer support
Configurable delta-sigma ADC with 8- to12-bit resolution[2]
• Programmable gain stage: ×0.25 to ×16
• 12-bit mode, 192-ksps, 66-dB signal to noise and distortion
ratio (SINAD), ±1-bit INL/DNL
Up to two SAR ADCs, each 12-bit at 1 Msps
Four 8-bit 8 Msps IDACs or 1 Msps VDACs
Four comparators with 95 ns response time
Four uncommitted opamps with 25 mA drive capability
Low voltage, ultra low power
Wide operating voltage range: 0.5 V to 5.5 V
High efficiency boost regulator from 0.5 V input to 1.8 V to
5.0 V output
3.1 mA at 6 MHz
Low-power modes including:
• 2 µA sleep mode with real time clock and low voltage detect
(LVD) interrupt
Four configurable multifunction analog blocks. Example
configurations are PGA, TIA. Mixer and sample and hold
• 300 nA hibernate mode with RAM retention
Versatile I/O system
CapSense support
Programming, debug, and trace
28 to 72 I/Os (62 GPIOs, 8 SIOs, 2 USBIOs[2]
)
Any GPIOs to any digital or analog peripheral routability
LCD direct drive from any GPIO, up to 46 × 16 segments
CapSense® support from any GPIO[3]
1.2 V to 5.5 V I/O interface voltages, up to four domains
Maskable, independent IRQ on any pin or port
Schmitt-trigger TTL inputs
All GPIOs configurable as open drain high/low,
pull-up/pull-down, High Z, or strong output
Configurable GPIO pin state at power-on reset (POR)
25 mA sink on SIO
Digital peripherals
JTAG (4 wire), serial-wire debug (SWD) (2 wire), single-wire
viewer (SWV), and TRACEPORT interfaces
Cortex-M3 flash patch and breakpoint (FPB) block
Cortex-M3 Embedded Trace Macrocell™ (ETM™)
generates an instruction trace stream.
Cortex-M3 data watchpoint and trace (DWT) generates data
trace information
Cortex-M3 Instrumentation Trace Macrocell (ITM) can be
used for printf-style debugging
DWT, ETM, andITMblockscommunicatewithoff-chipdebug
and trace systems via the SWV or TRACEPORT
Bootloader programming supportable through I2C, SPI,
20 to 24 programmable PLD based universal digital
UART, USB, and other interfaces
blocks (UDB)
Precision, programmable clocking
3 to 62 MHz internal oscillator over full temperature and
voltage range
4 to 25 MHz crystal oscillator for crystal PPM accuracy
Internal PLL clock generation up to 67 MHz
32.768-kHz watch crystal oscillator
Full CAN 2.0b 16 RX, 8 TX buffers[2]
Full-Speed (FS) USB 2.0 12 Mbps using internal oscillator[2]
Four 16-bit configurable timer, counter, and PWM blocks
67-MHz, 24-bit fixed point digital filter block (DFB) to
implement FIR and IIR filters
Low-power internal oscillator at 1, 33, and 100 kHz
Temperature and packaging
–40 °C to +85 °C degrees industrial temperature
68-pin QFN and 100-pin TQFP package options
Notes
1. AHB – AMBA (advanced microcontroller bus architecture) high-performance bus, an ARM data transfer bus
2. This feature on select devices only. See Ordering Information on page 113 for details.
3. GPIOs with opamp outputs are not recommended for use with CapSense.
Cypress Semiconductor Corporation
•
198 Champion Court
•
San Jose, CA 95134-1709
•
408-943-2600
Document Number: 001-84935 Rev. *C
Revised March 8, 2013
5秒后页面跳转
国产厂商思特威CMOS图像传感器芯片单月出货超1亿颗，技术创新引领行业发展
台积电5nm和3nm产能利用率达100%，半导体行业景气度持续攀升
AMD宣布全球裁员约1000人，调整战略聚焦增长
英伟达新AI芯片Rubin或提前半年亮相
微信公众号
抖音公众号
浙公网安备 33010502006866号 浙ICP备10014259号-119
营业执照ICP证
技术参数
数据手册
如果您发现信息不准确，
