CY7C1561KV18, CY7C1576KV18
CY7C1563KV18, CY7C1565KV18
PRELIMINARY
72-Mbit QDR™-II+ SRAM 4-Word Burst
Architecture (2.5 Cycle Read Latency)
Features
Configurations
■ Separate Independent Read and Write Data Ports
❐ Supports concurrent transactions
With Read Cycle Latency of 2.5 cycles:
CY7C1561KV18 – 8M x 8
■ 550 MHz Clock for High Bandwidth
CY7C1576KV18 – 8M x 9
CY7C1563KV18 – 4M x 18
CY7C1565KV18 – 2M x 36
■ 4-word Burst for Reducing Address Bus Frequency
■ Double Data Rate (DDR) Interfaces on both Read and Write
Ports (data transferred at 1100 MHz) at 550 MHz
Functional Description
■ Available in 2.5 Clock Cycle Latency
The CY7C1561KV18, CY7C1576KV18, CY7C1563KV18, and
CY7C1565KV18 are 1.8V Synchronous Pipelined SRAMs,
equipped with QDR-II+ architecture. Similar to QDR-II archi-
tecture, QDR-II+ architecture consists of two separate ports: the
read port and the write port to access the memory array. The
read port has dedicated data outputs to support read operations
and the write port has dedicated data inputs to support write
operations. QDR-II+ architecture has separate data inputs and
data outputs to completely eliminate the need to “turnaround” the
data bus that exists with common I/O devices. Each port is
accessed through a common address bus. Addresses for read
and write addresses are latched on alternate rising edges of the
input (K) clock. Accesses to the QDR-II+ read and write ports are
completely independent of one another. To maximize data
throughput, both read and write ports are equipped with DDR
interfaces. Each address location is associated with four 8-bit
words (CY7C1561KV18), 9-bit words (CY7C1576KV18), 18-bit
words (CY7C1563KV18), or 36-bit words (CY7C1565KV18) that
burst sequentially into or out of the device. Because data is trans-
ferred into and out of the device on every rising edge of both input
clocks (K and K), memory bandwidth is maximized while simpli-
fying system design by eliminating bus “turnarounds”.
■ Two Input Clocks (K and K) for precise DDR Timing
❐ SRAM uses rising edges only
■ Echo Clocks (CQ and CQ) simplify Data Capture inHigh Speed
Systems
■ Data Valid Pin (QVLD) to indicate Valid Data on the Output
■ Single Multiplexed Address Input Bus latches Address Inputs
for Read and Write Ports
■ Separate Port selects for Depth Expansion
■ Synchronous Internally Self-timed Writes
■ QDR™-II+ operates with 2.5 cycle read latency when DOFF is
asserted HIGH
■ OperatessimilartoQDR-IDevicewithoneCycleReadLatency
when DOFF is asserted LOW
■ Available in x8, x9, x18, and x36 Configurations
■ Full Data Coherency, providing Most Current Data
[1]
■ Core VDD = 1.8V± 0.1V; I/O VDDQ = 1.4V to VDD
❐ Supports both 1.5V and 1.8V I/O supply
■ HSTL Inputs and Variable Drive HSTL Output Buffers
■ Available in 165-Ball FBGA Package (13 x 15 x 1.4 mm)
■ Offered in both Pb-free and non Pb-free Packages
■ JTAG 1149.1 compatible Test Access Port
■ Phase-Locked Loop (PLL) for Accurate Data Placement
Table 1. Selection Guide
Depth expansion is accomplished with port selects, which
enables each port to operate independently.
All synchronous inputs pass through input registers controlled by
the K or K input clocks. All data outputs pass through output
registers controlled by the K or K input clocks. Writes are
conducted with on-chip synchronous self-timed write circuitry.
Description
Maximum Operating Frequency
Maximum Operating Current
550 MHz
500 MHz
500
450 MHz
450
400 MHz
400
Unit
MHz
mA
550
900
900
920
1310
x8
x9
830
760
690
830
760
690
x18
x36
850
780
710
1210
1100
1000
Note
1. The Cypress QDR-II+ devices surpass the QDR consortium specification and can support V
= 1.4V to V
.
DD
DDQ
Cypress Semiconductor Corporation
Document Number: 001-15878 Rev. *E
•
198 Champion Court
•
San Jose, CA 95134-1709
•
408-943-2600
Revised April 03, 2009
[+] Feedback
5秒后页面跳转
解析光耦仿真器：升级光耦合器技术的必要性
英伟达新一代Blackwell GPU过热问题致交付延迟
国产厂商思特威CMOS图像传感器芯片单月出货超1亿颗，技术创新引领行业发展
台积电5nm和3nm产能利用率达100%，半导体行业景气度持续攀升
微信公众号
抖音公众号
浙公网安备 33010502006866号 浙ICP备10014259号-119
营业执照ICP证
数据手册
如果您发现信息不准确，
