The Communications Edge TM
CV111-3A
UMTS-band High Linearity Downconverter
Product Information
Product Features
Product Description
Functional Diagram
• High dynamic range downconverter
The CV111-3A is a high linearity downconverter
designed to meet the demanding issues for performance,
functionality, and cost goals of current and next
generation mobile infrastructure basestations. It provides
high dynamic range performance in a low profile
surface-mount leadless package that measures 6 x 6 mm
square.
with integrated LO, IF, & RF amps
28
27
26
24
23
22
25
• RF: 1900 – 2200 MHz
• IF: 65 – 300 MHz
• +38 dBm Output IP3
RF OUT
GND
1
2
3
4
5
6
7
IF
21 IF OUT
IF Amp
GND
20
RF Amp
GND
GND
GND
BIAS
GND
LO IN
19
18
17
16
15
GND
• +21 dBm Output P1dB
• 5.3 dB Noise Figure
• +5V Single supply operation
• Pb-free 6mm 28-pin QFN package
• Low-side LO configuration
LO Driver Amp
GND
Functionality includes RF amplification, frequency
conversion and IF amplification, while an integrated LO
driver amplifier powers the passive mixer. The MCM is
implemented with reliable and mature GaAs MESFET
and InGaP HBT technology.
GND
RF
MIXRF
LO
8
9
10
12
13
14
11
Typical applications include frequency down conversion,
modulation and demodulation for receivers used in
CDMA, CDMA2000, W-CDMA / IMT2000, GPRS, and
EDGE 2.5G mobile infrastructure technologies for
UMTS frequency bands.
• Common footprint with other
PCS/ cellular versions
Top View
Specifications (1)
Parameters
Units
MHz
MHz
MHz
%
MHz
dB
dB
dBm
dBm
dBm
dB
Min
Typ
Max
Comments
RF Frequency Range
LO Frequency Range
IF Center Frequency Range
% Bandwidth around IF center frequency
IF Test Frequency
1900 – 2200
1600 – 2135
65 – 300
±7.5
240
20
See note 2
See note 3
SSB Conversion Gain
Gain Drift over Temp (-40 to 85 °C)
Output IP3
Output IP2
Output 1dB Compression Point
Noise Figure
Temp = 25 °C
Referenced to +25 °C
See note 4
±0.5
+38
+48
+21
5.3
See note 4
See note 5
LO Input Drive Level
LO-RF Isolation
LO-IF Isolation
dBm
dB
dB
-2.5
+2.5
0
40
25
PLO = 0 dBm
PLO = 0 dBm
Return Loss: RF Port
Return Loss: LO Port
Return Loss: IF Port
Operating Supply Voltage
Supply Current
dB
dB
dB
14
14
14
+5
V
+4.9
290
+5.1
480
72.1
160
mA
360
failures
FIT Rating
Junction Temperature
/
@ 70o C ambient, 90% confidence
See note 6
1E9 hrs
°C
1. Specifications when using the application specific circuit (shown on page 3) with a low side LO = 0 dBm in a downconverting application over the operating case temperature range.
2. IF matching components affect the center IF frequency. Proper component values for other IF center frequencies than shown can be provided by emailing to applications.engineering@wj.com.
3. The IF bandwidth of the converter is defined as 15% around any center frequency in its operating IF frequency range. The bandwidth is determined with external components. Specifications are valid around
the total ±7.5% bandwidth. ie. with a center frequency of 80 MHz, the specifications are valid from 80 ± 6 MHz.
4. Assumes the supply voltage = +5 V. OIP3 is measured with Δf = 1 MHz with IFout = 5 dBm / tone.
5. Assumes LO injection noise is filtered at the thermal noise floor, -174 dBm/Hz, at the RF, IF, and Image frequencies.
6. The maximum junction temperature ensures a minimum MTTF rating of 1 million hours of usage.
Absolute Maximum Rating
Ordering Information
Parameter
Rating
-40 to +85° C
-55 to +125° C
+6 V
Operating Case Temperature
Storage Temperature
DC Voltage
Part No.
Description
UMTS-band High Linearity Downconverter
CV111-3AF
(lead-free/RoHS-compliant 6x6mm QFN package)
Junction Temperature
RF Input (continuous)
+220 °C
+2 dBm
CV111-3APCB75 Fully Assembled Eval. Board, IF = 75MHz
CV111-3APCB240 Fully Assembled Eval. Board, IF = 240MHz
Operation of this device above any of these parameters may cause permanent damage.
Specifications and information are subject to change without notice
WJ Communications, Inc • Phone 1-800-WJ1-4401 • FAX: 408-577-6621 • e-mail: sales@wj.com • Web site: www.wj.com
Page 1 of 5 May 2006