CD4541B
CMOS Programmable Timer
High Voltage Types (20V Rating)
Data sheet acquired from Harris Semiconductor
SCHS085E – Revised September 2003
The output from this timer is the Q or Q output from the 8th,
10th, 13th, or 16th counter stage. The desired stage is chosen
using time-select inputs A and B (see Frequency Select Table).
Features
• Low Symmetrical Output Resistance, Typically 100Ω
at V
= 15V
DD
The output is available in either of two modes selectable via the
MODE input, pin 10 (see Truth Table). When this MODE input is
a logic “1”, the output will be a continuous square wave having
[ /Title
(CD45
41B)
/Sub-
ject
(CMO
S Pro-
gram-
mable
Timer
High
Volt-
age
Types
(20V
Rat-
ing))
/Autho
r ()
/Key-
words
(Har-
ris
Semi-
con-
ductor,
CD400
0,
metal
gate,
• Built-In Low-Power RC Oscillator
• Oscillator Frequency Range . . . . . . . . . . DC to 100kHz
N
a frequency equal to the oscillator frequency divided by 2 .
• External Clock (Applied to Pin 3) can be Used Instead
of Oscillator
With the MODE input set to logic “0” and after a MASTER
N
RESET is initiated, the output (assuming Q output has been
• Operates as 2 Frequency Divider or as a Single-
N-1
selected) changes from a low to a high state after 2
counts
Transition Timer
and remains in that state until another MASTER RESET pulse
is applied or the MODE input is set to a logic “1”.
• Q/Q Select Provides Output Logic Level Flexibility
• AUTO or MASTER RESET Disables Oscillator During
Reset to Reduce Power Dissipation
Timing is initialized by setting the AUTO RESET input (pin 5) to
logic “0” and turning power on. If pin 5 is set to logic “1”, the
AUTO RESET circuit is disabled and counting will not start until
after a positive MASTER RESET pulse is applied and returns
to a low level. The AUTO RESET consumes an appreciable
amount of power and should not be used if low-power operation
• Operates With Very Slow Clock Rise and Fall Times
• Capable of Driving Six Low Power TTL Loads, Three
Low-Power Schottky Loads, or Six HTL Loads Over
the Rated Temperature Range
is desired. For reliable automatic power-on reset, V
be greater than 5V.
should
DD
• Symmetrical Output Characteristics
• 100% Tested for Quiescent Current at 20V
• 5V, 10V, and 15V Parametric Ratings
The RC oscillator, shown in Figure 2, oscillates with a
frequency determined by the RC network and is calculated
using:
• Meets All Requirements of JEDEC Standard No. 13B,
“Standard Specifications for Description of ‘B’ Series
CMOS Devices”
Where f is between 1kHz
and 100kHz
1
----------------------------------
f =
2.3 R
C
TC TC
and R ≥ 10kΩ and ≈ 2R
S
TC
Description
CD4541B programmable timer consists of a 16-stage binary
counter, an oscillator that is controlled by external R-C compo-
nents (2 resistors and a capacitor), an automatic power-on
reset circuit, and output control logic. The counter increments
on positive-edge clock transitions and can also be reset via the
MASTER RESET input.
Ordering Information
TEMP. RANGE
o
PART NUMBER
CD4541BF3A
CD4541BE
( C)
PACKAGE
-55 to 125
-55 to 125
-55 to 125
-55 to 125
-55 to 125
-55 to 125
-55 to 125
-55 to 125
14 Ld CERDIP
14 Ld PDIP
14 Ld SOIC
14 Ld SOIC
14 Ld SOIC
14 Ld SOP
CD4541BM
CD4541BMT
CD4541BM96
CD4541BNSR
CD4541BPW
CD4541BPWR
Pinout
CD4541B
(CERDIP, PDIP, SOIC, SOP, TSSOP)
14 Ld TSSOP
14 Ld TSSOP
TOP VIEW
CMOS
, pdip,
cerdip,
mil,
mili-
tary,
R
C
1
2
3
4
5
6
7
14
13
12
V
DD
TC
NOTE: When ordering, use the entire part number. The suffixes 96
and R denote tape and reel. The suffix T denotes a small-quantity
reel of 250.
B
A
TC
R
S
NC
AUTO RESET
11 NC
10 MODE
mil
MASTER RESET
9
8
Q/Q SELECT
OUTPUT
V
SS
CAUTION: These devices are sensitive to electrostatic discharge. Users should follow proper IC Handling Procedures.
Copyright © 2003, Texas Instruments Incorporated
1
5秒后页面跳转
英伟达新AI芯片Rubin或提前半年亮相
苹果iPhone 17将全系采用三星/LG显示LTPO OLED面板
三星深化印度制造布局，供应链本地化进程加速
芯擎科技“星辰一号”自动驾驶芯片点亮成功，2025年量产在即
微信公众号
抖音公众号
浙公网安备 33010502006866号 浙ICP备10014259号-119
营业执照ICP证
数据手册
如果您发现信息不准确，
