BD83A44EFV-M BD83A44MUF-M
Description of Blocks – continued
Detect Conditions and Operation at Detection of Each Protection Function (All values in the table are Typ values)
Operation at Detection
Detect Condition
Protection Function
(Block Name)
No.
1
Load
DC/DC
Current
Driver
FAIL
[Detect]
[Release]
Switch Switching
Under Voltage
Lockout
VCC ≤ 4.10 V
or
VCC ≥ 4.25 V
and
High
(Note 5)
OFF
OFF
OFF
OFF
OFF
(UVLO)
VREG ≤ 3.95 V
VREG ≥ 4.10 V
Thermal Shutdown
LED
2
3
Tj ≥ 175 °C
Tj ≥ 175 °C
Tj ≤ 150 °C
Tj ≤ 150 °C
OFF
Low
Low
(TSDLED)
Thermal Shutdown
REG
OFF
OFF
OFF
ON
(TSDREG)
Overcurrent
Protection
(OCPL)
High
(Note 5)
4
5
ISW ≥ 3.6 A
ISW < 3.6 A
ON
ON
OFF
OFF
Overvoltage
Protection
(OVP)
VOVP ≥ 1.21 V
VOVP ≤ 1.16 V
ON
Low
Only
LED Open
Protection
(OPEN Det)
VLEDn(Note 1) ≤ 0.3 V
and
VEN = Low(Note 6)
or
detection Latch
6
7
ON
ON
ON
ON
LED pin
is OFF
Only
Low
VOVP ≥ 1.21 V
Detects UVLO
LED Short
Protection
Detects
VEN = Low(Note 6)
or
detection Latch
VLEDn(Note 1) ≥ 5.0 V
for 3.56 ms or more(Note 2)
LED pin
is OFF
Low
(SHORT Det)
Detects UVLO
Detects
VLEDn(Note 1) ≤ 0.3 V
or
Short Circuit
Protection
(SCP)(Note 3)
VEN = Low(Note 6)
or
Latch
Low
8
9
OFF
OFF
OFF
VOVP ≤ 0.1 V
Detects UVLO
for 3.56 ms or more
Detects
Input
voltage between the
Overcurrent
Protection
(OCPH)(Note 3)
ISET-GND
voltage between the
VCC-CSH pin ≥ 0.1 V
for 10 μs or more
VCC-CSH pin < 0.1 V
OFF
OFF
OFF
OFF
OFF
OFF
Low
Low
(Note 4)
ISET resistor ≤ 3.5 kΩ
ISET resistor > 3.5 kΩ
10 Short Protection
(ISET Pin Fault)
(when VADIM = VREG
)
(when VADIM = VREG)
(Note 1) LEDn indicates one of the LED1 to LED4 pins.
(Note 2) LED pin voltage of at least 1 channel shall be less than VLEDCTL(MIN) x 1.2. When LED pin voltages of all channels are 2.4 V or more, the LED short protection
does not operate. Since the 3.56 ms counter is counted up only when PWM = High, the time until SHORT Det is detected varies depending on PWM Duty.
(Note 3) When Short Circuit Protection (SCP) and Input Overcurrent Protection (OCPH) are detected at the same time, the operation of Input Overcurrent Protection
takes precedence.
(Note 4) When 56.96 ms elapses after the load switch is turned OFF, the load switch turns ON. At this time, when the voltage between the VCC-CSH pin ≥ 0.1 V, the
load switch, DC/DC switching, and current driver are turned OFF again. Also, when the voltage between the VCC-CSH pin < 0.1 V, Self Diagnosis is
performed and restarted.
(Note 5) When pulled up to any voltage, it becomes High output.
(Note 6) The Low width of EN need 10 µs or more.
www.rohm.com
TSZ02201-0T2T0B200460-1-2
© 2022 ROHM Co., Ltd. All rights reserved.
9/47
TSZ22111 • 15 • 001
08.May.2023 Rev.001