5秒后页面跳转
AT49BV4096A-90TJ PDF预览

AT49BV4096A-90TJ

更新时间: 2024-11-25 03:24:51
品牌 Logo 应用领域
爱特美尔 - ATMEL 光电二极管
页数 文件大小 规格书
16页 359K
描述
Flash, 256KX16, 90ns, PDSO48, 12 X 20 MM, PLASTIC, MO-142DD, TSOP1-48

AT49BV4096A-90TJ 数据手册

 浏览型号AT49BV4096A-90TJ的Datasheet PDF文件第2页浏览型号AT49BV4096A-90TJ的Datasheet PDF文件第3页浏览型号AT49BV4096A-90TJ的Datasheet PDF文件第4页浏览型号AT49BV4096A-90TJ的Datasheet PDF文件第5页浏览型号AT49BV4096A-90TJ的Datasheet PDF文件第6页浏览型号AT49BV4096A-90TJ的Datasheet PDF文件第7页 
Features  
Single-voltage Read/Write Operation: 2.7V to 3.6V (BV), 3.0V to 3.6V (LV)  
Fast Read Access Time – 70 ns  
Internal Erase/Program Control  
Sector Architecture  
– One 8K Word (16K Bytes) Boot Block with Programming Lockout  
– Two 4K Word (8K Bytes) Parameter Blocks  
– One 240K Word (480K Bytes) Main Memory Array Block  
Fast Sector Erase Time – 10 Seconds  
Byte-by-byte or Word-by-word Programming – 30 µs Typical  
Hardware Data Protection  
Data Polling for End of Program Detection  
Low Power Dissipation  
– 25 mA Active Current  
– 50 µA CMOS Standby Current  
Typical 10,000 Write Cycles  
4-megabit  
(512K x 8/  
256K x 16)  
Single 2.7-volt  
Battery-Voltage™  
Flash Memory  
Description  
The AT49BV/LV4096A is a 3-volt, 4-megabit Flash memory organized as 524,288  
words of 8 bits each or 256K words of 16 bits each. Manufactured with Atmel’s  
advanced nonvolatile CMOS technology, the device offers access times to 70 ns with  
power dissipation of just 67 mV at 2.7V read. When deselected, the CMOS standby  
current is less than 50 µA.  
The device contains a user-enabled “boot block” protection feature. The  
AT49BV/LV4096A locates the boot block at lowest order addresses (“bottom boot”).  
AT49BV4096A  
AT49LV4096A  
Not Recommended  
for New Design  
Contact Atmel to discuss  
the latest design in trends  
and options  
To allow for simple in-system reprogrammability, the AT49BV/LV4096A does not  
require high input voltages for programming. Reading data out of the device is similar  
to reading from an EPROM; it has standard CE, OE and WE inputs to avoid bus con-  
tention. Reprogramming the AT49BV/LV4096A is performed by first erasing a block of  
data and then programming on a byte-by-byte or word-by-word basis.  
Pin Configurations  
Pin Name  
A0 - A17  
CE  
Function  
Addresses  
Chip Enable  
Output Enable  
Write Enable  
Reset  
OE  
WE  
RESET  
VPP  
VPP can be left unconnected or connected to VCC, GND, 5V or  
12V. The input has no effect on the operation of the device.  
I/O0 - I/O15  
I/O15(A-1)  
Data Inputs/Outputs  
I/O15 (Data Input/Output, Word Mode)  
A-1 (LSB Address Input, Byte Mode)  
BYTE  
NC  
Selects Byte or Word Mode  
No Connect  
Rev. 1618H–FLASH–4/04  

与AT49BV4096A-90TJ相关器件

型号 品牌 获取价格 描述 数据表
AT49BV4096A-90TL ATMEL

获取价格

Flash, 256KX16, 90ns, PDSO48, 12 X 20 MM, PLASTIC, MO-142DD, TSOP1-48
AT49BV4096AT ATMEL

获取价格

4-Megabit 512K x 8/ 256K x 16 CMOS Flash Memory
AT49BV4096AT-12RC ATMEL

获取价格

4-Megabit 512K x 8/ 256K x 16 CMOS Flash Memory
AT49BV4096AT-12RI ATMEL

获取价格

4-Megabit 512K x 8/ 256K x 16 CMOS Flash Memory
AT49BV4096AT-12TC ATMEL

获取价格

4-Megabit 512K x 8/ 256K x 16 CMOS Flash Memory
AT49BV4096AT-12TI ATMEL

获取价格

4-Megabit 512K x 8/ 256K x 16 CMOS Flash Memory
AT49BV512 ATMEL

获取价格

512K 64K x 8 Single 2.7-volt Battery-Voltage Flash Memory
AT49BV512-12JC ATMEL

获取价格

512K 64K x 8 Single 2.7-volt Battery-Voltage Flash Memory
AT49BV512-12JI ATMEL

获取价格

512K 64K x 8 Single 2.7-volt Battery-Voltage Flash Memory
AT49BV512-12JJ ATMEL

获取价格

Flash, 64KX8, 120ns, PQCC32, PLASTIC, LCC-32