5秒后页面跳转
AT29C040A-15JU PDF预览

AT29C040A-15JU

更新时间: 2024-09-21 03:04:47
品牌 Logo 应用领域
爱特美尔 - ATMEL /
页数 文件大小 规格书
17页 346K
描述
Flash, 512KX8, 150ns, PQCC32, PLASTIC, MS-016AE, LCC-32

AT29C040A-15JU 数据手册

 浏览型号AT29C040A-15JU的Datasheet PDF文件第2页浏览型号AT29C040A-15JU的Datasheet PDF文件第3页浏览型号AT29C040A-15JU的Datasheet PDF文件第4页浏览型号AT29C040A-15JU的Datasheet PDF文件第5页浏览型号AT29C040A-15JU的Datasheet PDF文件第6页浏览型号AT29C040A-15JU的Datasheet PDF文件第7页 
Features  
Fast Read Access Time – 90 ns  
5-volt Only Reprogramming  
Sector Program Operation  
– Single Cycle Reprogram (Erase and Program)  
– 2048 Sectors (256 Bytes/Sector)  
– Internal Address and Data Latches for 256 Bytes  
Internal Program Control and Timer  
Hardware and Software Data Protection  
Two 16K Bytes Boot Blocks with Lockout  
Fast Sector Program Cycle Time – 10 ms  
DATA Polling for End of Program Detection  
Low Power Dissipation  
4-megabit  
(512K x 8)  
5-volt Only  
256-byte Sector  
Flash Memory  
– 40 mA Active Current  
– 100 µA CMOS Standby Current  
Typical Endurance > 10,000 Cycles  
Single 5V 10% Supply  
CMOS and TTL Compatible Inputs and Outputs  
Green (Pb/Halide-free) Packaging Option  
AT29C040A  
1. Description  
The AT29C040A is a 5-volt only in-system Flash Programmable and Erasable Read  
Only Memory (PEROM). Its 4 megabits of memory is organized as 524,288 words by  
8 bits. Manufactured with Atmel’s advanced nonvolatile CMOS EEPROM technology,  
the device offers access times up to 90 ns, and a low 220 mW power dissipation.  
When the device is deselected, the CMOS standby current is less than 100 µA. The  
device endurance is such that any sector can typically be written to in excess of  
10,000 times. The programming algorithm is compatible with other devices in Atmel’s  
5-volt only Flash family.  
To allow for simple in-system reprogrammability, the AT29C040A does not require  
high input voltages for programming. Five-volt-only commands determine the opera-  
tion of the device. Reading data out of the device is similar to reading from an  
EPROM. Reprogramming the AT29C040A is performed on a sector basis; 256 bytes  
of data are loaded into the device and then simultaneously programmed.  
During a reprogram cycle, the address locations and 256 bytes of data are internally  
latched, freeing the address and data bus for other operations. Following the initiation  
of a program cycle, the device will automatically erase the sector and then program  
the latched data using an internal control timer. The end of a program cycle can be  
detected by DATA polling of I/O7. Once the end of a program cycle has been  
detected, a new access for a read or program can begin.  
0333K–FLASH–2/05  

与AT29C040A-15JU相关器件

型号 品牌 获取价格 描述 数据表
AT29C040A-15PC ATMEL

获取价格

4-Megabit 512K x 8 5-volt Only 256-Byte Sector CMOS Flash Memory
AT29C040A-15PI ATMEL

获取价格

4-Megabit 512K x 8 5-volt Only 256-Byte Sector CMOS Flash Memory
AT29C040A-15TC ATMEL

获取价格

4-Megabit 512K x 8 5-volt Only 256-Byte Sector CMOS Flash Memory
AT29C040A-15TCT/R ATMEL

获取价格

Flash, 512KX8, 150ns, PDSO32, PLASTIC, TSOP-32
AT29C040A-15TI ATMEL

获取价格

4-megabit (512K x 8) 5-volt Only 256-byte Sector Flash Memory
AT29C040A-15TIT/R ATMEL

获取价格

Flash, 512KX8, 150ns, PDSO32, PLASTIC, TSOP-32
AT29C040A-15TU ATMEL

获取价格

Flash, 512KX8, 150ns, PDSO32, 8 X 20 MM, PLASTIC, MO-142BD, TSOP1-32
AT29C040A-15TUT/R ATMEL

获取价格

Flash, 512KX8, 150ns, PDSO32, PLASTIC, TSOP-32
AT29C040A-20DC ETC

获取价格

x8 Flash EEPROM
AT29C040A-20DI ETC

获取价格

x8 Flash EEPROM