CONDUCTIVE POLYMER ALUMINUM SOLID CAPACITORS
Surface Mount
@Super low ESR, impedance and high heat resistance have been obtained by using
conductive polymer as electrolyte
@Rated voltage range : 2.5 to 25Vdc, case size range : F6.3B5.2L to F10B12.2L
(Case code HC0 and JC0 newly added)
@Suitable for DC-DC converters, voltage regulators and decoupling applications used to
computer motherboards etc.
@High heat resistance to reflow soldering (See reflow soldering conditions)
@Pb-free design
SPECIFICATIONS
?
Items
Characteristics
Category
Temperature Range
-55 to +105C
Rated Voltage Range 2.5 to 25Vdc
Capacitance Tolerance P20% (M)
(at 20C, 120Hz)
(at 105C)
Surge Voltage
Rated voltageB1.15V
Leakage Current
Shall not exceed values shown in STANDARD RATINGS.
(at 20C after 2 minutes)
Dissipation Factor
(tane)
0.12 max.
(at 20C, 120Hz)
Low Temperature
Characteristics
Z(
-
25C)/Z(+20C)[1.15
(Max. Impedance Ratio) Z(
-55C)/Z(+20C)[1.25
(at 100kHz)
Endurance
The following specifications shall be satisfied when the capacitors are restored to 20C after the rated voltage is applied for 2000 hours
at 105C.
Appearance
Capacitance change
DF (tanE)
No significant damage
[P20% of the initial value
[150% of the initial specified value
[150% of the initial specified value
[The initial specified value
ESR
Leakage current
Bias Humidity
Surge Voltage
Failure Rate
The following specifications shall be satisfied when the capacitors are restored to 20C after subjecting them to the DC rated voltage at
60C, 90 to 95% RH for 500 hours.
Appearance
Capacitance change
DF (tanE)
No significant damage
[P20% of the initial value
[150% of the initial specified value
[150% of the initial specified value
[The initial specified value
ESR
Leakage current
The capacitors shall be subjected to 1000 cycles each consisting of charge with the surge voltage specified at 105C for 30 seconds
through a protective resistor(R=1kO) and discharge for 5 minutes 30 seconds.
Appearance
Capacitance change
DF (tanE)
No significant damage
[P20% of the initial value
[150% of the initial specified value
[150% of the initial specified value
[The initial specified value
ESR
Leakage current
1% per 1000 hours maximum (Confidence level 60% at 105C)
*Note : If any doubt arises, measure the leakage current after following voltage treatment.
Voltage treatment : DC rated voltage are applied to the capacitors for 120 minutes at 105C.
DIMENSIONS [mm]
MARKING
?
?
EX) PXA16VC39M
@Terminal Code : A
W
Size code fD
L
A
B
C
W
P
A905
F55
F60
H70
J80
HC0
JC0
6.3 5.2 6.6 6.6 7.2 0.5 to 0.8 1.9
6.3 5.7 6.6 6.6 7.2 0.5 to 0.8 1.9
39
16V
8
6.7 8.3 8.3 9.0 0.7 to 1.1 3.1
10 7.7 10.3 10.3 11.0 0.7 to 1.1 4.5
12.0 8.3 8.3 9.0 0.7 to 1.1 3.1
8
10 12.2 10.3 10.3 11.0 0.7 to 1.1 4.5
0.3max.
AP0.2
LP0.3 (Note)
Note : LP0.5 for HC0 and JC0
PART NUMBERING SYSTEM
?
1
2
3
4
5
6
7
8
9
10
11 12 13
14
15 16 17
18
A P X A A A A A R A A A A M A A A N
Supplement code
Size code
Capacitance tolerance code
Capacitance code (ex. 10MF:100,100MF:101)
Taping code
Terminal code
Voltage code (ex. 6.3V:6R3,10V:100)
Series code
Category
Please refer to "A guide to global code (conductive polymer type)"
(1/2)
CAT. No. E1001E