CONDUCTIVE POLYMER ALUMINUM SOLID CAPACITORS
Surface Mount
NPCAPTM-PXASeries
PXE P40
Super low ESR, impedance and high heat resistance have been obtained by using
conductive polymer as electrolyte
・
Lower ESR
Rated voltage range : 2.5 to 25Vdc, case size range : 4×5.2L to 10×12.2L
・
・
φ
φ
Suitable for DC-DC converters, voltage regulators and decoupling applications used on
computer motherboards etc.
PXA
Solvent resistant type (see PRECAUTIONS AND GUIDELINES)
RoHS Compliant
Halogen Free
・
・
・
SPECIFICATIONS
◆
Items
Characteristics
Category
Temperature Range
-55 to +105
℃
Rated Voltage Range
Capacitance Tolerance
Surge Voltage
2.5 to 25Vdc
20% (M)
(at 20 , 120Hz)
±
℃
Rated voltage 1.15 (Rated voltage 2.5 to 20Vdc, 25Vdc) / Rated voltage 1.00 (Rated voltage 23Vdc
)
(at 105
)
℃
×
×
Leakage Current
Dissipation Factor
Shall not exceed values shown in STANDARD RATINGS.
(at 20 after 2 minutes)
℃
0.12 max.
(at 20 , 120Hz)
(tan
)
℃
δ
Low Temperature
Z(-25 )/Z(+20
)
)
1.15
1.25
℃
℃ ≦
Characteristics
Z(-55 )/Z(+20
℃
℃ ≦
(at 100kHz)
(Max. Impedance Ratio)
Endurance
The following specifications shall be satisfied when the capacitors are restored to 20 after the rated voltage is applied for 15,000 hours
℃
(F45 : 3,000 hours) at 105
.
℃
Appearance
Capacitance change
No significant damage
20% of the initial value
≦±
D.F. (tan
ESR
Leakage current
)
150% of the initial specified value
150% of the initial specified value
The initial specified value
δ
≦
≦
≦
Bias Humidity
Surge Voltage
Failure Rate
The following specifications shall be satisfied when the capacitors are restored to 20 after subjecting them to the DC rated voltage at
℃
60 , 90 to 95% RH for 1,000 hours(F45 : 500 hours).
℃
Appearance
Capacitance change
No significant damage
20% of the initial value
≦±
D.F. (tan
ESR
Leakage current
)
150% of the initial specified value
150% of the initial specified value
The initial specified value
δ
≦
≦
≦
The capacitors shall be subjected to 1,000 cycles each consisting of charge with the surge voltage specified at 105 for 30 seconds
℃
through a protective resistor(R=1k ) and discharge for 5 minutes 30 seconds.
Ω
Appearance
Capacitance change
No significant damage
20% of the initial value
≦±
D.F. (tan
ESR
Leakage current
)
150% of the initial specified value
150% of the initial specified value
The initial specified value
δ
≦
≦
≦
0.5% per 1,000 hours maximum (Confidence level 60% at 105
)
℃
*Note : If any doubt arises, measure the leakage current after the following voltage treatment.
Voltage treatment : DC rated voltage is applied to the capacitors for 120 minutes at 105℃.
DIMENSIONS [mm]
MARKING
◆
◆
●
µ
EX) 16V39 F
Terminal Code : A
Size code
D55
E60
F45
F55
φ
4
5
D
L
A
B
C
W
P
W
5.2 4.3 4.3 5.1 0.5 to 0.8 1.0
5.7 5.3 5.3 5.9 0.5 to 0.8 1.4
6.3 4.4 6.6 6.6 7.2 0.5 to 0.8 1.9
6.3 5.2 6.6 6.6 7.2 0.5 to 0.8 1.9
6.3 5.7 6.6 6.6 7.2 0.5 to 0.8 1.9
A
15L
39
16V
F60
H70
HC0
J80
8
8
6.7 8.3 8.3 9.0 0.7 to 1.1 3.1
12.0 8.3 8.3 9.0 0.7 to 1.1 3.1
0.3max.
A±0.2
10 7.7 10.3 10.3 11.0 0.7 to 1.1 4.5
10 12.2 10.3 10.3 11.0 0.7 to 1.1 4.5
L±
0.3 (Note)
Note : L+0.1/-0.2 for F45
0.5 for HC0 and JC0
JC0
L±
PART NUMBERING SYSTEM
◆
1
2
3
4
5
6
7
8
9
10
11 12 13
14
15 16 17
18
A P X A
A R A
M
G
Supplement code
Size code
Capacitance tolerance code
Capacitance code (ex. 10µF:100,100µF:101)
Taping code
Terminal code
Voltage code (ex. 6.3V:6R3,10V:100)
Series code
Category
Please refer to "Product code guide (conductive polymer type)"
Product specifications in this catalog are subject to change without notice.Request our product specifications before purchase and/or use. Please use our products based on the information contained in this catalog and product specifications.
CAT. No. E1001Q
42