Angle Position Sensors
AN9 Sensors
Thin, programmable, non-contact magnetic position sensors
capable of continuous rotation with dual outputs
Description
The AN9 Series sensors are non-contact, intrinsically linear angle position sensors with two independent outputs. The sensors
operate through the use of Hall Effect technology with magnetic fields generated by permanent magnets. They provide a linear
change in voltage output (ratiometric to the input voltage) corresponding to an angular rotation of the input shaft.
Features
Typical Applications
Angular position sensor with high tolerance for misalignment
Implement (fork lift, agricultural trailer hitch,
etc.) position sensing
Steer, throttle by wire
Non-contact angular position sensing and full 360° rotation
Dual independent (fully redundant) outputs assure high reliability
Custom programming available for: angle range, slope, PWM
output, custom magnets – contact factory
No mechanical interface means no parts to wear out or jam
Comes with 18 AWG 305 mm (12”) wire leads
RoHS Compliant
Gear selection
Zero-contact encoder alternative
Replacement for smart bearings
Outboard trim sensing
IP68*
Maximum air gap of 5.5 mm (0.22”)**
Environmental Specifications
Vibration
Operating Temperature
Storage Temperature
15g sinusoidal, 9.26g RMS axial; 40 Hz – 2 kHz all 3 axes
-40 °C to 125 °C (-40 °F to 257 °F)
-40 °C to 150 °C (-40 °F to 302 °F)
IP68*
Ingress Protection
*submerged in 22±3 °C water for 1 hour at 2 m depth
Electrical Specifications
Input Voltage
5.0 VDC ± 10%
Output Voltage
10% to 90% of input (see graph for voltage vs. rotation angle
characteristics)
Input Current
Output Current
Output Accuracy
Output Linearity
14 mA typ., 16 mA max.
-8 mA to 8 mA
±3.5%
±3.5%
Maximum Overvoltage
Absolute Max. Output Current
Output Type
16 VDC
±30 mA
Analog (PWM available)
Mechanical Specifications
Housing Material
Mechanical Travel
Maximum Air Gap**
Glass Reinforced Plastic
0° to 360° (continuous)
5.5 mm (0.22")
**with AS500106 magnet carrier
Maximum Center-To Center Offset
2 mm radial (magnet to center)
Note: When used with AS500106 Magnet Carrier; user is responsible for determining characteristics when using other magnets.
Products
Sensing Range
Wires
www.switches-sensors.zf.com
Page 1 of 2, last update 2017-01-05, Specifications subject to change without notice.
#NP#_TY9vb4IwEMa/CumrLZ PZFlDwHZ 2dYQ7E P5vDNCGV 4mxGqKHVLDF+95Xt zS655O653+XuuYKqApMr 6A6JABOAIILgNr Bi37HhlJv6DvmhF+ARRgGE8MEmvGdDMA BC9pvcgt82rLDv 61RWndLqYJyt6kS PJVMrkyLYZ XHwQecLCItiNQtf3ndpE WbYIoeTJYoJY1/aeL49wJhshbxIceYNY+StTGg 5a9SeN+WaN7Uuk1actelkL6jmb KRqNWN5v nJeN5kTr4ijj7yr GbMOuD7WtbHjdd1q1dmCtp+N1Md/0zLOopJmj0JVvZPT39PPGU7jfIbHIzyaL3O42KKlV+B0E1rG/CIheYr INCKuhyh2fRqN3Z hQ6BLohcjHEbYJ brcf_#NP#