5秒后页面跳转
AN-1030 PDF预览

AN-1030

更新时间: 2024-10-29 12:54:11
品牌 Logo 应用领域
CYMBET /
页数 文件大小 规格书
6页 494K
描述
EVAL-08 Frequently Asked Questions & Troubleshooting

AN-1030 数据手册

 浏览型号AN-1030的Datasheet PDF文件第2页浏览型号AN-1030的Datasheet PDF文件第3页浏览型号AN-1030的Datasheet PDF文件第4页浏览型号AN-1030的Datasheet PDF文件第5页浏览型号AN-1030的Datasheet PDF文件第6页 
Preliminary  
AN-1030  
Application Note  
EVAL-08 Frequently Asked Questions & Troubleshooting Guide  
Features  
The CBC-EVAL-08 is a demonstration kit combining a  
solar panel energy transducer with the EnerChip EH  
CBC5300 Energy Harvesting module that has two  
50 µAh EnerChip Batteries. The EnerChips provide  
storage and starting power for the energy harvesting  
module. The purpose of this demonstration platform  
is to enable designers to quickly develop Energy  
Harvesting applications. A block diagram of the  
EVAL-08 is shown in Figure 1.  
Figure 2: CBC-EVAL-08 EVAL Kit - 3.55 x 2 in.  
Control  
Lines  
Vout  
The power management block is used to protect  
the EnerChips from discharging too deeply in low  
ambient light conditions, or abnormally high current  
load conditions. The power management block  
also ensures that the load is powered up with a  
smooth power on transition. The power management  
block has a control line (CHARGE) for indication to  
the system controller that the energy harvester is  
charging the EnerChips. A control line input (BATOFF)  
is available for the controller to disconnect itself  
from the EnerChips when it is desired to conserve  
battery life for as long as possible in prolonged low  
ambient light conditions.  
Photovoltaic  
Cell  
Connector  
Power  
Management  
Boost  
Converter  
Charge  
Control  
2 - EnerChip  
CBC050  
Figure 1: EnerChip EVAL-08 Demo Kit Block Diagram  
The EVAL-08 shown in Figure 2 with the EnerChip EH  
Module mounted on the Solar board with 100 µAh  
capacity.  
System Description  
The photovoltaic cells convert ambient light energy  
into electrical energy. The output voltage of the  
photovoltaic cells is too low to charge the EnerChips  
and power the rest of the system directly, so a  
boost converter is used to boost the photovoltaic  
cell voltage to the voltage needed to charge the  
EnerChips.  
There are two connectors on the EVAL-08 for  
connection to target devices to be powered. Either  
connector can be used for low power microcontroller  
based systems. In the case of a low-power wireless  
end device, the EVAL-08 has storage energy for up to  
1000 transmissions - depending on protocol used -  
in no/low ambient light conditions.  
The charge control block continuously monitors  
the output of the boost converter. If the output of  
the boost converter falls below the voltage needed  
to charge the EnerChips, the charge controller will  
disconnect the boost converter from the EnerChips.  
This prevents the EnerChips from back powering the  
boost converter in low ambient light conditions.  
Microcontroller systems that are powered by the  
EVAL-08 should contain firmware that is “Energy  
Harvesting Aware” and take advantage of the power  
management status and control signals in the CBC-  
EVAL-08.  
©2008 Cymbet Corporation • Tel: +1-763-633-1780 • www.cymbet.com  
Doc AN-72-1030 Rev02  
Page 1 of 7  

与AN-1030相关器件

型号 品牌 获取价格 描述 数据表
AN-1032 FAIRCHILD

获取价格

Performance Restrictions Associated with 3.5 Watts SO-8 Power MOSFETs
AN10327 NXP

获取价格

TDA856x and TDA8571J power amplifiers
AN1034 INTERSIL

获取价格

Analog Switch and Multiplexer Applications
AN-1036 CYMBET

获取价格

Using the EnerChip CC in Energy Harvesting Designs
AN10365 NXP

获取价格

Surface mount reflow soldering
AN-1039 ADI

获取价格

Correcting Imperfections in IQ Modulators to Improve RF Signal Fidelity
AN10397 NXP

获取价格

How to use the SC18IM700 to control any I2C-bus device
AN104 SMSC

获取价格

AN104
AN1040 MICROCHIP

获取价格

A broad portfolio of high performance, best-in-class Serial Memory Products to meet all yo
AN-1040 CYMBET

获取价格

EVAL Kit GUI Software and TI Firmware Readme