5秒后页面跳转
AMIS-53000-I/A PDF预览

AMIS-53000-I/A

更新时间: 2024-01-31 06:06:29
品牌 Logo 应用领域
AMI /
页数 文件大小 规格书
99页 4395K
描述
Frequency Agile Transceiver

AMIS-53000-I/A 技术参数

生命周期:Obsolete包装说明:QFP, QFP32,.35SQ,32
Reach Compliance Code:compliant风险等级:5.84
Is Samacsys:NJESD-30 代码:S-PQFP-G32
端子数量:32最高工作温度:85 °C
最低工作温度:-40 °C封装主体材料:PLASTIC/EPOXY
封装代码:QFP封装等效代码:QFP32,.35SQ,32
封装形状:SQUARE封装形式:FLATPACK
电源:2.2/3.3 V认证状态:Not Qualified
子类别:Other Telecom ICs最大压摆率:70 mA
表面贴装:YES技术:CMOS
温度等级:INDUSTRIAL端子形式:GULL WING
端子节距:0.8 mm端子位置:QUAD
Base Number Matches:1

AMIS-53000-I/A 数据手册

 浏览型号AMIS-53000-I/A的Datasheet PDF文件第4页浏览型号AMIS-53000-I/A的Datasheet PDF文件第5页浏览型号AMIS-53000-I/A的Datasheet PDF文件第6页浏览型号AMIS-53000-I/A的Datasheet PDF文件第8页浏览型号AMIS-53000-I/A的Datasheet PDF文件第9页浏览型号AMIS-53000-I/A的Datasheet PDF文件第10页 
AMIS-53000 Frequency Agile Transceiver  
Data Sheet  
1.4.2.5.  
Manchester Data Encoding  
The AMIS-53000 can encode the data as NRZ or Manchester.  
1.4.2.6.  
Oscillators  
The AMIS-53000 requires a single external crystal working with the internal VCO and PLL to generate frequencies from 300MHz to  
928MHz. The AMIS-53000 has internal capacitors that eliminate the need for external load capacitors when using a typical 24MHz  
external crystal. The VCO requires an external inductor and capacitor (including internal capacitance) to produce the desired transmit  
or receive RF frequency. The AMIS-53000 generates the desired RF transmit and receive frequencies from 300MHz to 928MHz by  
selecting the proper inductor and capacitor value along with programming the frequency in the AMIS-53000. A patented Quick Start  
circuit is used to force the crystal oscillator on to the desired frequency in microseconds rather than in milliseconds.  
A low power internal 10kHz oscillator provides the timing for Sniff, Burst and housekeeping. The AMIS-53000 self-calibration circuits  
can tune this oscillator to within two percent of 10kHz.  
1.4.2.7.  
Interface Serial Bus  
The AMIS-53000 has separate interfaces for data and control. The transfer of TX/RX data between the AMIS-53000 and an external  
host/controller is done with a 3-wire serial interface or a 4-wire SPI compatible serial interface. Control information is written to the  
AMIS-53000 registers or read from the AMIS-53000 registers using either a 3-wire serial interface or a 2-wire I2C compatible serial  
interface.  
Once the AMIS-53000 configuration registers have data written to them for various operational modes such as, TX, RX, Sniff or other,  
placing the AMIS-53000 into one of these modes is accomplished through a single write to the command register.  
TX/RX Data Interface  
The transmit or receive data interface of the AMIS-53000 can be programmed to be either a proprietary 3-wire serial interface or a  
4-wire SPI compatible serial bus. The data interface can be set up to do either data transfers into a buffer in the AMIS-53000 or  
streaming data (data is transmitted as it is received by the AMIS-53000 or data is sent to the host/controller as it is recovered in the  
AMIS-53000 receiver). When using the buffered data mode, the AMIS-53000 can be the master or slave, but it must be the master to  
do streaming data.  
Control Interface  
Once the AMIS-53000 is first powered on, an external host/controller sets the type of interface to the AMIS-53000 (3-wire or I2C) by  
simply writing to the AMIS-53000 with the desire protocol. The AMIS-53000 will continue to use that interface protocol until power is  
removed from the AMIS-53000. The AMIS-53000 is always a slave device for the control interface.  
AMI Semiconductor – Aug. 05, Rev. 1.0  
7
www.amis.com  

与AMIS-53000-I/A相关器件

型号 品牌 描述 获取价格 数据表
AMIS-53000-M ONSEMI IC,TRANSCEIVER CIRCUIT FOR TELECOMMUNICATIONS,CMOS,QFP,32PIN,PLASTIC

获取价格

AMIS-53000-M AMI Frequency Agile Transceiver

获取价格

AMIS-5300-A ONSEMI IC,TRANSCEIVER CIRCUIT FOR TELECOMMUNICATIONS,CMOS,QFP,32PIN,PLASTIC

获取价格

AMIS-53050 AMI Frequency Agile Transceiver

获取价格

AMIS-53050-I/A AMI Frequency Agile Transceiver

获取价格

AMIS-53050-I/A-XTD AMI Telecom IC,

获取价格