Datasheet > AFCT-5765TLZ

AFCT-5765TLZ

更新时间： 2024-09-17 21:13:31

品牌	Logo	应用领域
安华高科 - AVAGO		通信放大器光纤
页数	文件大小	规格书
20页	488K
描述
FIBER OPTIC TRANSCEIVER, 1261-1360nm, 155Mbps(Tx), 155Mbps(Rx), BOARD/PANEL MOUNT, LC CONNECTOR, ROHS COMPLIANT PACKAGE-20

阅读下载

中文翻译

获取价格

技术参数
数据手册

如果您发现信息不准确，欢迎纠错

AFCT-5765TLZ 技术参数

是否无铅：	不含铅	是否Rohs认证：	符合
生命周期：	Transferred	Reach Compliance Code：	compliant
ECCN代码：	5A991.B.5.A	HTS代码：	8517.62.00.50
风险等级：	5.72	其他特性：	SFF-8074I, SFF-8472
主体宽度：	13.4 mm	主体高度：	8.5 mm
主体长度或直径：	55.2 mm	内置特性：	AMPLIFIER
通信标准：	GR-253, ITU-T-G.957, OC-12, STM-4	连接类型：	LC CONNECTOR
数据速率（接收）：	155 Mbps	数据速率（发送）：	155 Mbps
发射极/检测器类型：	LASER DIODE, PIN PHOTODIODE	光纤设备类型：	TRANSCEIVER
光纤类型：	SMF	JESD-609代码：	e4
安装特点：	BOARD/PANEL MOUNT	最高工作温度：	85 °C
最低工作温度：	-40 °C	最大工作波长：	1360 nm
最小工作波长：	1261 nm	标称工作波长：	1300 nm
标称光功率输出：	0.07 mW	灵敏度：	-31 dBm
子类别：	Fiber Optic Transceivers	最大供电电压：	3.5 V
最小供电电压：	3.1 V	标称供电电压：	3.3 V
表面贴装：	NO	端子面层：	Gold (Au)
Base Number Matches：	1

AFCT-5765TLZ 数据手册

Table 2. Pin description

Name

Function/Description

MSA Notes

VeeT

Transmitter Ground

TX Fault

TX Disable

MOD-DEF2

MOD-DEF1

MOD-DEF0

Rate Select

LOS

Transmitter Fault Indication

Transmitter Disable - Module disables on high or open

Module Deﬁnition 2 - Two wire serial ID interface

Module Deﬁnition 1 - Two wire serial ID interface

Module Deﬁnition 0 - Grounded in module

Not Connected

Note 1

Note 2

Note 3

Loss of Signal

Note 4

VeeR

Receiver Ground

VeeR

Receiver Ground

VeeR

Receiver Ground

RD-

Inverse Received Data Out

Received Data Out

Note 5

RD+

VeeR

Receiver Ground

VccR

Receiver Power - 3.3 V 5%

Transmitter Power - 3.3 V 5%

Transmitter Ground

Note 6

VccT

VeeT

TD+

Transmitter Data In

Note 7

TD-

Inverse Transmitter Data In

Transmitter Ground

VeeT

Notes:

1. TX Fault is an open collector/drain output, which should be pulled up with a 4.7K – 10KΩ resistor on the host board. Pull up voltage between

2.0 V and VccT, R+0.3 V. When high, output indicates a laser fault of some kind. Low indicates normal operation. In the low state, the output will

be pulled to < 0.8 V. By default, TX_FAULT is set to trigger on hardware faults only.

2. TX Disable input is used to shut down the laser output per the state table below with an external 4.7 - 10 KΩ pull-up resistor.

Low (0 - 0.8 V): Transmitter on

Between (0.8 V and 2.0 V): Undeﬁned

High (2.0 - 3.465 V): Transmitter Disabled

Open: Transmitter Disabled

3. MOD-DEF 0,1,2. These are the module deﬁnition pins. They should be pulled up with a 4.7 - 10 KΩ resistor on the host board to a supply less

than VccT +0.3 V or VccR+0.3 V.

MOD-DEF 0 is grounded by the module to indicate that the module is present

MOD-DEF 1 is clock line of two wire serial interface for optional serial ID

MOD-DEF 2 is data line of two wire serial interface for optional serial ID

4. LOS (Loss of Signal) is an open collector/drain output which should be pulled up externally with a 4.7K - 10 KΩ resistor on the host board to a

supply < VccT,R+0.3 V. When high, this output indicates the received optical power is below the worst case receiver sensitivity (as deﬁned by

the standard in use). Low indicates normal operation. In the low state, the output will be pulled to < 0.8 V.

5. RD-/+: These are the diﬀerential receiver outputs. They are ac coupled 100Ω diﬀerential lines which should be terminated with 100Ω diﬀerential

at the user SERDES. The ac coupling is done inside the module and is thus not required on the host board. The voltage swing on these lines will

be between 320 and 2000 mV diﬀerential (160 - 1000 mV single ended) when properly terminated.

6. VccR and VccT are the receiver and transmitter power supplies. They are deﬁned as 3.135 - 3.465 V at the SFP connector pin. The maximum sup-

ply current is 250 mA and the associated inrush current will be no more than 30 mA above steady state after 500 nanoseconds.

7. TD-/+: These are the diﬀerential transmitter inputs. They are ac coupled diﬀerential lines with 100Ω diﬀerential termination inside the module.

The ac coupling is done inside the module and is thus not required on the host board. The inputs will accept diﬀerential swings of 500 - 2400

mV (250 - 1200 mV single ended), though it is recommended that values between 500 and 1200 mV diﬀerential (250 - 600 mV single ended) be

used for best EMI performance.

1...4 5 678 9 10...20

中文翻译

下载PDF

与AFCT-5765TLZ相关器件

型号	品牌	获取价格	描述	数据表
AFCT-5765TPZ	AVAGO	获取价格	Families of Small Form Factor Pluggable (SFP) Optical Transceivers
AFCT-5765xxZ	BOARDCOM	获取价格	Single-Mode SFP Optical Transceivers with Optional DMI for Gigabit Ethernet and Fibre Chan
AFCT-5765xxZ	AVAGO	获取价格	Single-Mode SFP Optical Transceivers
AFCT-57D5ANPZ	AVAGO	获取价格	16GFC SFP Digital Diagnostic SFP, 850 nm, 16G/8G/4G Low Voltage (3.3 V) Fibre Channel Opti
AFCT-57D5ATPZ	AVAGO	获取价格	16GFC SFP Digital Diagnostic SFP, 850 nm, 16G/8G/4G Low Voltage (3.3 V) Fibre Channel Opti
AFCT-57D5ATPZ_15	AVAGO	获取价格	Fibre Channel RoHS Compliant Optical Transceiver
AFCT-57J5ANPZ	BOARDCOM	获取价格	Family of Singlemode SFP Transceivers for Long Reach SONET OC-48
AFCT-57J5ANPZ	AVAGO	获取价格	Family of Singlemode SFP Transceivers for Long Reach SONET OC-48
AFCT-57J5APZ	AVAGO	获取价格	Digital Diagnostic SFP, 1310nm, Fabry Perot 3.072/2.4576 Gb/s, RoHS OBSAI/CPRI Compatible
AFCT-57J5ATPZ	AVAGO	获取价格	1310nm, 20km, 3.072/2.4576 Gb/s, Low Voltage (3.3 V) Digital Diagnostic Optical Transceive

与AFCT-5765TLZ相关文章

摩尔斯微电子在美国约书亚树国家公园测试 Wi-Fi HaLow
2024-09-18

16
贸泽上架Tallysman TW5386智能GNSS天线
2024-09-18

14
SL74HC10N：高性能三输入与非门解析
2024-09-03

93
AIC1781A 电池充电控制器深度解析
2024-09-03

82

产品中心

服务支持

精选活动

关于我们

帮助中心

AFCT-5765TLZ

AFCT-5765TLZ 技术参数

AFCT-5765TLZ 数据手册

与AFCT-5765TLZ相关器件

与AFCT-5765TLZ相关文章

您还可以找

产品中心

服务支持

精选活动

关于我们

帮助中心

AFCT-5765TLZ

AFCT-5765TLZ 技术参数

AFCT-5765TLZ 数据手册

与AFCT-5765TLZ相关器件

与AFCT-5765TLZ相关文章

您还可以找

您在本页遇到什么问题？