FemtoClock® NG Octal Universal
Frequency Translator
8T49N281
Datasheet
General Description
Features
The 8T49N281 has a fractional-feedback PLL that can be used as a
jitter attenuator or frequency translator. It is equipped with six integer
and two fractional output dividers, allowing the generation of up to 8
different output frequencies, ranging from 8kHz to 1GHz. Three of
these frequencies are completely independent of each other and the
inputs. The other five are related frequencies. The eight outputs may
select among LVPECL, LVDS or LVCMOS output levels.
• Supports SDH/SONET and Synchronous Ethernet clocks
including all FEC rate conversions
• Two differential outputs meet jitter limits for 100G Ethernet and
STM-256/OC-768
• <0.3ps RMS (including spurs): 12kHz to 20MHz
• All outputs <0.5ps RMS (including spurs) 12kHz to 20MHz
• Operating modes: locked to input signal, holdover and free-run
• Initial holdover accuracy of ±50ppb
This functionality makes it ideal to be used in any frequency
translation application, including 1G, 10G, 40G and 100G
Synchronous Ethernet, OTN, and SONET/SDH, including ITU-T
G.709 (2009) FEC rates. The device may also behave as a frequency
synthesizer.
• Accepts two LVPECL, LVDS, LVHSTL, HCSL or LVCMOS
input clocks
• Accepts frequencies ranging from 8kHz up to 875MHz
• Auto and manual input clock selection with hitless switching
• Clock input monitoring, including support for gapped clocks
The 8T49N281 accepts up to two differential or single-ended input
clocks and a crystal input. The PLL can lock to either input clock, but
both input clocks must be related in frequency.
• Phase-Slope Limiting and Fully Hitless Switching options to
The device supports hitless reference switching between input
clocks. The device monitors both input clocks for Loss of Signal
(LOS). It generates an alarm when an input clock failure is detected.
Automatic and manual hitless reference switching options are
supported. LOS behavior can be set to support gapped or un-gapped
clocks.
control output phase transients
• Operates from a 10MHz to 40MHz fundamental-mode crystal
• Generates eight LVPECL /LVDS or sixteen LVCMOS output
clocks
• Output frequencies ranging from 8kHz up to 1.0GHz (diff)
• Output frequencies ranging from 8kHz to 250MHz (LVCMOS)
The 8T49N281 supports holdover with an initial accuracy of ±50ppB
from the point where the loss of all applicable input reference(s) has
been detected. It maintains a historical average operating point that
may be returned to in holdover at a limited phase slope.
• Four General Purpose I/O pins with optional support for status &
control:
The device places no constraints on input to output frequency
conversion, supporting all FEC rates, including the new revision of
ITU-T Recommendation G.709 (2009), most with 0ppm conversion
error.
• Four Output Enable control inputs may be mapped to any of the
eight outputs
• Lock, Holdover & Loss-of-Signal status outputs
• Open-drain Interrupt pin
• Programmable PLL bandwidth settings:
The PLL has a register-selectable loop bandwidth from 0.5Hz to
512Hz.
• 0.5Hz, 1Hz, 2Hz, 4Hz, 8Hz, 16Hz, 32Hz, 64Hz, 128Hz, 256Hz
Each output supports individual phase delay settings to allow
output-output alignment.
or 512Hz
• Optional Fast Lock function
The device supports Output Enable inputs and Lock, Holdover and
LOS status outputs.
The device is programmable through an I2C interface. It also
supports I2C master capability to allow the register configuration to
be read from an external EEPROM.
• Programmable output phase delays in steps as small as 16ps
• Register programmable through I2C or via external I2C EEPROM
• Bypass clock paths for system tests
• Power supply modes
VCC / VCCA / VCCO
3.3V / 3.3V / 3.3V
Applications
3.3V / 3.3V / 2.5V
3.3V / 3.3V / 1.8V (LVCMOS)
2.5V / 2.5V / 3.3V
2.5V / 2.5V / 2.5V
2.5V / 2.5V / 1.8V (LVCMOS)
• OTN or SONET / SDH equipment Line cards (up to OC-192, and
supporting FEC ratios)
• OTN de-mapping (Gapped Clock and DCO mode)
• Gigabit and Terabit IP switches / routers including support of
• Power down modes support consumption as low as 1.5W (see
Section, “Power Dissipation and Thermal Considerations” for
details)
Synchronous Ethernet
• Wireless base station baseband
• Data communications
• -40°C to 85°C ambient operating temperature
• Package: 56QFN, lead-free RoHs (6)
©2016 Integrated Device Technology, Inc.
1
Revision 7, October 26, 2016
5秒后页面跳转
MBRS340T3G手册解读：参数说明、产品特性及应用
PMOS管背靠背连接：串联还是并联？
高压电解电容的分类与选型策略
数码管：基本概念、分类、技术发展及市场趋势
微信公众号
抖音公众号
浙公网安备 33010502006866号 浙ICP备10014259号-119
营业执照ICP证
数据手册
如果您发现信息不准确，
