FemtoClock® NG Octal Universal
Frequency Translator
8T49N282
Datasheet
General Description
Features
The 8T49N282 has two independent, fractional-feedback PLLs that
can be used as jitter attenuators and frequency translators. It is
equipped with six integer and two fractional output dividers, allowing
the generation of up to eight different output frequencies, ranging
from 8kHz to 1GHz. Four of these frequencies are completely
independent of each other and the inputs. The other four are related
frequencies. The eight outputs may select among LVPECL, LVDS or
LVCMOS output levels.
• Supports SDH/SONET and Synchronous Ethernet clocks
including all FEC rate conversions
• Two differential outputs meet jitter limits for 100G Ethernet and
STM-256/OC-768
• <0.3ps RMS (including spurs): 12kHz to 20MHz
• All outputs <0.5ps RMS (including spurs) 12kHz to 20MHz
• Operating modes: locked to input signal, holdover and free-run
• Initial holdover accuracy of ±50ppb
This functionality makes it ideal to be used in any frequency
translation application, including 1G, 10G, 40G and 100G
Synchronous Ethernet, OTN, and SONET/SDH, including ITU-T
G.709 (2009) FEC rates. The device may also behave as a frequency
synthesizer.
• Accepts up to four LVPECL, LVDS, LVHSTL, HCSL or LVCMOS
input clocks
• Accepts frequencies ranging from 8kHz up to 875MHz
• Auto and manual input clock selection with hitless switching
• Clock input monitoring, including support for gapped clocks
The 8T49N282 accepts up to four differential or single-ended input
clocks and a crystal input. Each of the two internal PLLs can lock to
different input clocks which may be of independent frequencies. The
other two input clocks are intended for redundant backup of the
primary clocks and must be related in frequency to their primary.
• Phase-Slope Limiting and Fully Hitless Switching options to
control output phase transients
• Operates from a 10MHz to 40MHz fundamental-mode crystal
• Generates eight LVPECL / LVDS or 16 LVCMOS output clocks
• Output frequencies ranging from 8kHz up to 1.0GHz (diff)
• Output frequencies ranging from 8kHz to 250MHz (LVCMOS)
The device supports hitless reference switching between input
clocks. The device monitors all input clocks for Loss of Signal (LOS),
and generates an alarm when an input clock failure is detected.
Automatic and manual hitless reference switching options are
supported. LOS behavior can be set to support gapped or un-gapped
clocks.
• Eight General Purpose I/O pins with optional support for status
and control
• Eight Output Enable control inputs
• Lock, Holdover and Loss-of-Signal status outputs
• Open-drain Interrupt pin
• Write-protect pin to prevent configuration registers being altered
• Programmable PLL bandwidth settings for each PLL:
The 8T49N282 supports holdover for each PLL. The holdover has an
initial accuracy of ±50ppB from the point where the loss of all
applicable input reference(s) has been detected. It maintains a
historical average operating point for each PLL that may be returned
to in holdover at a limited phase slope.
• 0.5Hz, 1Hz, 2Hz, 4Hz, 8Hz, 16Hz, 32Hz, 64Hz, 128Hz, 256Hz
or 512Hz
The device places no constraints on input to output frequency
conversion, supporting all FEC rates, including the new revision of
ITU-T Recommendation G.709 (2009), most with 0ppm conversion
error.
• Optional Fast Lock function
• Programmable output phase delays in steps as small as 16ps
• Register programmable through I2C / SPI or via external I2C
Each PLL has a register-selectable loop bandwidth from 0.5Hz to
512Hz.
EEPROM
• Bypass clock paths for system tests
Each output supports individual phase delay settings to allow
output-output alignment.
• Power supply modes:
VCC / VCCA / VCCO
3.3V / 3.3V / 3.3V
The device supports Output Enable inputs and Lock, Holdover and
LOS status outputs.
3.3V / 3.3V / 2.5V
3.3V / 3.3V / 1.8V (LVCMOS)
2.5V / 2.5V / 3.3V
The device is programmable through an I2C interface. It also
supports I2C master capability to allow the register configuration to
be read from an external EEPROM. The user may select whether the
programming interface uses I2C protocols or SPI protocols, however
in SPI mode, read from the external EEPROM is not supported.
2.5V / 2.5V / 2.5V
2.5V / 2.5V / 1.8V (LVCMOS)
• Power down modes support consumption as low as 1.7W (see
Power Dissipation and Thermal Considerations section for
details)
• -40°C to 85°C ambient operating temperature
• Package: 72QFN, lead-free RoHs (6)
Applications
• OTN or SONET / SDH equipment Line cards (up to OC-192, and
supporting FEC ratios)
• OTN de-mapping (Gapped Clock and DCO mode)
• Gigabit and Terabit IP switches / routers including support of
Synchronous Ethernet
• Wireless base station baseband
• Data communications
©2016 Integrated Device Technology, Inc.
1
Revision H, October 26, 2016
5秒后页面跳转
解析光耦仿真器：升级光耦合器技术的必要性
英伟达新一代Blackwell GPU过热问题致交付延迟
国产厂商思特威CMOS图像传感器芯片单月出货超1亿颗，技术创新引领行业发展
台积电5nm和3nm产能利用率达100%，半导体行业景气度持续攀升
微信公众号
抖音公众号
浙公网安备 33010502006866号 浙ICP备10014259号-119
营业执照ICP证
数据手册
如果您发现信息不准确，
