5秒后页面跳转
308983-2 PDF预览

308983-2

更新时间: 2024-10-29 01:07:31
品牌 Logo 应用领域
泰科 - TE /
页数 文件大小 规格书
4页 631K
描述
These dies crimp SOLISTRAND terminals on solid or stranded copper wire sizes 8 and 6.

308983-2 数据手册

 浏览型号308983-2的Datasheet PDF文件第2页浏览型号308983-2的Datasheet PDF文件第3页浏览型号308983-2的Datasheet PDF文件第4页 
Instruction Sheet  
Crimping Dies 68312-1  
and 68313-1 for  
SOLISTRAND* Terminals  
408-2674  
31 MAY 13 Rev A  
1. INTRODUCTION  
2.1. Die Installation  
This instruction sheet provides instructions on product  
application and a maintenance and inspection  
procedure for crimping dies 68312-1 and 68313-1  
used in machine 68250-1.  
1. Refer to the table in Figure 1 and select the die  
number for the wire size being used. Wire size  
displayed on dies must match wire size stamped  
under terminal tongue.  
These dies crimp SOLISTRAND terminals on solid or  
stranded copper wire sizes 8 and 6.  
2. TURN OFF MAIN POWER SWITCH, disconnect  
machine from power supply.  
Dies are coated with preservative to prevent rust and  
corrosion. Wipe preservative from dies, particularly  
from crimping surfaces.  
3. Remove front applicator guard, then depress  
terminal extractor, (see Figure 2), and pivot it away  
from crimping die holder.  
Section 2 of this publication, “INSTRUCTIONS”,  
provides personal safety, die installation and wire  
preparation information. Section 3 features a terminal  
and splice “CRIMP INSPECTION” procedure.  
Section 4 contains a “MAINTENANCE AND  
INSPECTION PROCEDURE” which will enable you to  
establish and maintain a die certification program.  
4. With tape release lever “up”, insert moving  
(upper) die into die holder and tighten holding  
screw. See Figure 2.  
5. Insert stationary (lower) die into die holder and  
tighten holding screw. See Figure 2.  
6. Pivot terminal extractor to vertical position and  
reinstall applicator guard.  
For further instructions relative to the machine, tooling  
adjustment, tape loading, etc., refer to instructions  
packaged with the machine.  
7. Lower tape release lever.  
8. Connect machine to power supply and turn on  
main power switch.  
NOTE  
NOTE  
i
Dimensions are in metric units with [inches in brackets].  
Figures and illustrations are for reference only and are  
not drawn to scale.  
Holding  
Screw  
Moving Die  
Holder  
Moving  
Die  
2. INSTRUCTIONS  
DANGER  
Avoid personal injury. Always disconnect machine from  
!
power supply when performing adjustments, die  
installation or removal, and machine maintenance.  
Always keep guards and covers in place during normal  
machine operation.  
Moving  
Die  
Tape  
Release  
Lever  
Stationary  
Die  
Holding  
Screw  
Stationary  
Die Holder  
Terminal  
Extractor  
Stationary  
Die  
Figure 2  
2.2. Die Removal  
STRIP LENGTH  
WIRE  
SIZE  
DIE PART  
NUMBER  
1. TURN OFF MAIN POWER SWITCH, disconnect  
machine from power supply.  
MIN  
MAX  
8
6
68312-1  
68313-1  
8.33 [.328]  
9.93 [.391]  
9.12 [.359]  
10.72 [.422]  
2. Remove front applicator guard, then depress  
terminal extractor and pivot it away from crimping  
die holder.  
Figure 1  
©2013 Tyco Electronics Corporation, a TE Connectivity Ltd. company TOOLING ASSISTANCE CENTER 1-800-722-1111 This controlled document is subject to change.  
1 of 4  
All Rights Reserved  
*Trademark  
PRODUCT INFORMATION 1-800-522-6752  
For latest revision and Regional Customer Service,  
visit our website at www.te.com  
TE Connectivity, TE connectivity (logo), and TE (logo) are trademarks. Other logos, product and/or company names may be trademarks of their respective owners.  

与308983-2相关器件

型号 品牌 获取价格 描述 数据表
308984-1 TE

获取价格

These dies crimp SOLISTRAND terminals on solid or stranded copper wire sizes 8 and 6.
308984-2 TE

获取价格

These dies crimp SOLISTRAND terminals on solid or stranded copper wire sizes 8 and 6.
3089SERIES ETC

获取价格

Power Dividers, 2, 3, 4, 6 and 8-Way 800-900,
308-AP6P0823-000 AMPHENOL

获取价格

D Subminiature Connector, 15 Contact(s), Male, Solder Terminal, Plug,
308-AS3C0211-000H AMPHENOL

获取价格

D Subminiature Connector, 26 Contact(s), Female, Solder Terminal, Receptacle,
308-AS9C0413-000 AMPHENOL

获取价格

D Subminiature Connector, 15 Contact(s), Female, Crimp Terminal, Receptacle,
308B120KBO1 VISHAY

获取价格

2 (50.8 mm) Single Turn Conductive Plastic Precision Potentiometer
308-BP3C0011-038H AMPHENOL

获取价格

D Subminiature Connector, 44 Contact(s), Male, Solder Terminal, Plug,
308-BP3C0112-000 AMPHENOL

获取价格

D Subminiature Connector, 25 Contact(s), Male, Solder Terminal, Plug,
308-BP3C0411-000H AMPHENOL

获取价格

D Subminiature Connector, 44 Contact(s), Male, Solder Terminal, Plug,