5秒后页面跳转
捷配首页

Datasheet > 2DA31PFO
2DA31PFO PDF预览

2DA31PFO

更新时间： 2024-02-03 06:08:17
品牌 Logo 应用领域
埃梯梯 - ITT 连接器
页数 文件大小 规格书
10页 607K
描述
D Subminiature Connector, 31 Contact(s), Male, 0.075 inch Pitch, Crimp Terminal, Hole .087-.098,

阅读下载

获取价格

2DA31PFO 技术参数

生命周期：ActiveReach Compliance Code：compliant
ECCN代码：EAR99HTS代码：8536.69.40.30
风险等级：5.7其他特性：POLARIZED
主体宽度：0.494 inch主体深度：0.319 inch
主体长度：1.541 inch连接器类型：D SUBMINIATURE CONNECTOR
联系完成配合：GOLD联系完成终止：GOLD
触点性别：MALE触点材料：COPPER ALLOY
触点模式：STAGGERED触点电阻：9 m Ω
触点样式：RND PIN-SKTDIN 符合性：NO
空壳：YES滤波功能：NO
IEC 符合性：NO最大插入力：3.336 N
绝缘电阻：5000000000 Ω绝缘体材料：GLASS FILLED POLYAMIDE
JESD-609代码：e4MIL 符合性：NO
插接触点节距：0.075 inch插接信息：MULTIPLE MATING PARTS AVAILABLE
混合触点：NO安装选项1：HOLE .087-.098
安装选项2：LOCKING安装类型：CABLE AND PANEL
装载的行数：3选件：GENERAL PURPOSE
额定电流（信号）：5 A可靠性：COMMERCIAL
外壳面层：CADMIUM外壳材料：STEEL
外壳尺寸：2/A子类别：D Type Connectors
端接类型：CRIMP触点总数：31
最大线径：22 AWG最小线径：26 AWG
Base Number Matches：1

2DA31PFO 数据手册

 浏览型号2DA31PFO的Datasheet PDF文件第4页浏览型号2DA31PFO的Datasheet PDF文件第5页浏览型号2DA31PFO的Datasheet PDF文件第6页浏览型号2DA31PFO的Datasheet PDF文件第7页浏览型号2DA31PFO的Datasheet PDF文件第8页浏览型号2DA31PFO的Datasheet PDF文件第10页 
The Centi Line - .075" Contact Spacing  
2D/CTA  
2D/CTA CENTI-LOCTM Connectors Assembly Instructions  
The Double Density D/CTA CENTI-LOC Connectors  
are highly reliable and simple connectors to use.  
There are a few helpful suggestions that will assure  
complete satisfaction when followed:  
1. The following instructions should be followed.  
2. The proper crimp tool and locator (if required)  
must be used. These tools have been designed  
for use with this product. Substitutions of crimp-  
ing equipment may result in connector failure at  
the assembly operation.  
3. After crimping a contact to a lead it is of vital  
importance that the proper tool be used to assure  
seating the contact in the insulator in the proper  
position. Any substitution of insertion tools may  
result in over or under insertion of the contact  
which may damage the retention system of the  
insulator.  
4. The female (socket) side of the connector has  
been designed with a controlled float to allow for  
ease of mating. To avoid reducing this float or  
causing a splaying of the contacts, any unneces-  
sary strain caused by clamping the leads too  
close to the rear of the connector should be  
avoided.  
Use of recommended tooling together with proper  
assembly techniques will pay dividends in reliability  
and reduced costs.  
2D Assembly Instructions  
WIRE STRIPPING  
CONTACT CRIMPING  
.100  
(2.54)  
Using the proper crimp tool and locator, insert the  
contact into the locator. Insert the stripped end of the  
wire into the contact crimp pot, and crimp the contact to  
the wire. Squeeze the handles firmly to insure a proper  
crimp (tool will not release if crimping is incomplete).  
NOTE: Contact stop must be changed in tool locator  
when crimping pin and socket contacts.  
Cut the wires to length required and strip .100" of  
insulation from the end to be crimped. Check for  
cut or broken wires and frayed insulation.  
CONTACT INSERTION  
2. Using a firm, steady pressure, push the contact into  
the cavity until the resilient internal shoulder in the  
insulator snaps into the locking groove in the contact.  
The shoulder of the tool tip bottoms against the rear  
of the insulator, preventing over-insertion. Repeat for  
balance of contacts.  
1. Place the proper insertion tip in the  
insertion/-extraction handle and put the tip over the  
wire as shown. The tool tip will butt up against the  
crimp pot. Connector must be firmly supported  
during both insertion and extraction operations.  
CONTACT EXTRACTION  
1. For contact extraction, remove the insertion tool  
tip and replace it with the proper extraction tool tip.  
(The socket tip will fit into the socket, and the pin  
tip will slide over the pin bundle). Insert the tool tip  
into the contact cavity: (the pin tip will butt up  
against the shoulder of the pin contact, and the  
socket tip will bottom out in the socket contact.)  
2. Apply a firm, steady pressure until the contact is  
released from the internal shoulder in the insulator. The  
shoulder of the tool tip bottom against the insulator  
face to prevent damage to the internal shoulder.  
Remove the tool tip and pull the contact from the rear  
of the connector. Repeat for the balance of contacts to  
be removed.  
Dimensions shown in inch (mm)  
Specifications and dimensions subject to change  
www.ittcannon.com  
68  
1...678910

下载PDF

与2DA31PFO相关器件

型号 品牌 描述 获取价格 数据表
2DA31S ITT D Subminiature Connector, 31 Contact(s), Female, 0.075 inch Pitch, Crimp Terminal, Hole .1

获取价格
2DA31SBRF172 ITT D Type Connector, 31 Contact(s), Female, 0.075 inch Pitch, Solder Terminal, #4-40, Plug

获取价格
2DA31SBRF172FO ITT D Type Connector, 31 Contact(s), Female, 0.075 inch Pitch, Solder Terminal, #4-40, Plug

获取价格
2DA31SBRF173 ITT D Type Connector, 31 Contact(s), Female, 0.075 inch Pitch, Solder Terminal, #4-40, Plug

获取价格
2DA31SBRF173FO ITT D Type Connector, 31 Contact(s), Female, 0.075 inch Pitch, Solder Terminal, #4-40, Plug

获取价格
2DA31SBRP ITT D Subminiature Connector, 31 Contact(s), Male, 0.075 inch Pitch, Solder Terminal, #4-40, P

获取价格

与2DA31PFO相关文章

您还可以找


热门产品
PCB打样/小批量
铝基板
BOM智能配单
PCBA制造
钣金
精密CNC
模具注塑
薄膜开关
精选活动
PCBA打样特惠
四六层板品质升级
铝基板品质升级
一体化电子制造
DFM下载
服务支持
企业认证
产品展示
工厂展示
工艺能力
积分商城
关于捷配
捷配简介
企业文化
公司动态
人才招聘
联系我们
帮助中心
下单流程
付款流程
开票流程
常见问题
全球PCB制造服务专线 400-613-0088

工作时间：9:00-21:00

CEO邮箱：ceo@jiepei.com

投诉邮箱：tousu@jiepei.com

捷配网-微信公众号 微信公众号
捷配网-微信公众号 抖音公众号
资质认证：
合作快递：
支付方式：
Copyright © 2024 Jiepei.com Inc. All Rights Reserved. 版权所有:杭州捷配信息科技有限公司 浙公网安备 33010502006866号 浙ICP备10014259号-119 营业执照ICP证