10DCPE_4 series
10W - Single Output DC-DC Converter - Ultra Wide Input Range -
High Isolated & Regulated
DC-DC Converter
10 Watt
The 10DCPE_4 series is a regulated DC-DC converter with an ultra-wide and ult-
ra-high DC input of 100-1000VDC. The products feature high efficiency, high
reliability, high insulation and a high level of safety protection. This type of
power supply is widely used in renewable energy industries such as photovol-
taic, power generation, energy storage, inverters and high-voltage DC conver-
sions. The converters provide multiple protection features and guarantee stable
and safe operating environments even under abnormal working conditions. For
extremely harsh EMC environment, we recommend using the application circuit
show in Design Reference of this datasheet.
10:1 ultra-wide input voltage
range: 100 ~ 1000VDC
Operating temperature:
-40°C ~ +70°C
Reverse input voltage
protection
Over voltage protection
Short circuit protection (SCP)
Input against reverse
protection
High reliability, long life,
three years warranty
EN62109 safety approval
(pending)
4000VAC high isolation
voltage
High efficiency,
low ripple & noise
Common specifications
Short circuit protection:
Temperature rise at full load:
Cooling:
Output specifications
Continuous, automatic recovery
25°C MAX (Ta = 25°C, 100% load)
Free air convection
-40°C~+70°C
Item
Test condition
Min
Typ
0.5
Max
1
Units
%
Line regulation
Load regulation
0.5
1
1
%
%
Operation temperature range:
Storage temperature range:
Case temperature:
Output voltage
accuracy
2
-40°C ~+105°C
90°C MAX
Ripple & Noise*
20MHz Bandwidth
100
200
mVp-
p
Welding temperature:
Wave-soldering: 260 5°Cꢀ time:5~10s
Manual-welding: 360 10°Cꢀ time:3~5s
Under input volta-
ge protection
Under voltage protection
range: 175~185V
Under voltage release range:
185~195V
Hot swap:
Forbidden
Case Material Grade:
Black flame-retardant and heat-
resistant plastic (UL94V-0)
Over input voltage
protection
• (Feedback-clamp) Voltage
limited < 7.5V
Install:
PCB
Storage humidity range:
Temperature coefficient:
Delay time:
< 95% (%RH)
0.02%ꢁ°C MAX
500ms MAX
>300,000 hours
*Test ripple and noise by “parallel cable” method.
MTBF (MIL-HDBK-217F@25°C):
Example:
10DCPE_05S4
10 = 10Watt; DC = DIP Case; P = Photovoltaic; E = series; 05 = 5Vout;
S = Single output; 4 = 4kVAC isolation;
Input specifications
Item
Test condition
Min
100
Typ
Max
Units
VDC
Input voltage range
Input current
1000
• 200VDC input
• 600VDC input
• 1000VDC input
38
15
8
mA
mA
mA
External input fuse
1Aꢁ1500VDC, required
Note:
Isolation specifications
1. Unless otherwise specified, all specifications above are measured at rated
input voltage and rated output load, TA = 25°C, humidity < 75%ꢀ
2. All specifications stated in this datasheet are subject to the above listed
models only. For specifications of non-standard models, please contact our
technical support team.
Item
Test condition
Tested for 1 minute
Min
Typ
Max
Units
VAC
MΩ
Isolation voltage
4000
100
Isolation resistance Test at 500VDC
Page 1 of 6
GAPTEC-Electronic GmbH & Co. KG
sales@gaptec-electronic.com – www.gaptec-electronic.com
10DCPE_4 – Rev. 2020-1.3
Specifications subject to change without notice.