1
Optoway
XPS-2340W-CXX0G
***********************************************************************************************************************************************************************
XPS-2340W-CXX0G
(RoHS Compliant)
10Gbps / CWDM XFP Single-Mode Optical Transceiver for 10GbE / 10GFC
**********************************************************************************************************************************************************************
FEATURES
DESCRIPTION
l Support 9.95 Gbps to 10.5 Gbps
l Complaint with XFP MSA
XPS-2340W-CXX0G series transceiver is designed for
single-mode fibre serial optical data communications such as
10G Ethernet 10GBASE-LR/LW and 10G Fibre Channel
1200-SM-LL-L.
l Compliant to IEEE 802.3ae 10GBASE-LR/LW
l Compliant to 10GFC 1200-SM-LL-L
l Compliant with XFI 10G Serial Electrical Interface
l Maximum Link Length of 40 km
l Uncooled 6-λ CWDM DFB LD: 1270 nm to 1370 nm
l 2-Wire Interface for Integrated Digital Diagnostic
Monitoring
l XFI Loopback Mode
l No reference Clock required
l Only Required +3.3 V Power Supply
l Power Consumption < 2 W
This module is designed for single mode fiber and
operates at a nominal wavelength of CWDM wavelength.
There are six center wavelengths available from 1270 nm to
1330 nm, with each step 20 nm. A guaranteed minimum
optical link budget of 16 dB is offered. The transceiver
consists of two sections: The transmitter section consists of a
directly modulated uncooled CWDM DFB laser, driver and
signal conditioner. The receiver section incorporates a PIN
photodiode integrated with a trans-impedance preamplifier
(TIA) and signal conditioner.
The module is with the XFP 30-pin connector to allow
hot plug capability. Integrated Tx and Rx signal conditioners
provide high jitter-tolerance for full XFI compliance and no
external reference clock required. The internally ac coupled
high speed serial I/O simplifies interfacing to external
circuitry. Only single 3.3V power supply is needed. The
optical output can be disabled by LVTTL logic high-level
input of TX_DIS. Loss of signal (RX_LOS) output is
provided to indicate the loss of an input optical signal of
receiver.
l RoHS Compliant
l -5 to 70oC Case Operating Temperature
l Duplex LC Connector
APPLICATIONS
l 10GBASE-LR at 10.3125 Gb/s
l 10GBASE-LW at 9.953 Gb/s
l 10GFC at 10.51875 Gb/s
LASER SAFETY
This single-mode transceiver is a Class 1 laser product. It
complies with IEC-60825 and FDA 21 CFR 1040.10 and
1040.11. The transceiver must be operated within the
specified temperature and voltage limits. The optical ports
of the module shall be terminated with an optical connector
or with a dust plug.
A serial EEPROM in the transceiver allows the user to
access transceiver digital diagnostic monitoring and
configuration data via the 2-wire XFP Management
Interface. This interface uses a single address, A0h, with a
memory map divided into a lower and upper area. Basic
digital diagnostic data is held in the lower area while specific
data is held in a series of tables in the high memory area.
ORDER INFORMATION
P/No.
Bit Rate
(Gb/s)
10GBASE
Power
Budget
(dB)
Wavelength
(nm)
Package
Case Temp
(oC)
RoHS
Compliant
XPS-2340W-CXX0G
9.95 – 10.52
> 16
CWDM*
XFP with DMI
-5 to 70
Yes
CWDM* Wavelength (0 to 70oC)
Central
Wavelength
Min.
(nm)
Typ.
(nm)
Max.
(nm)
Label
Central
Wavelength
Min.
(nm)
Typ.
Max.
(nm)
Label
(nm)
1330
1350
1370
C27
C29
C31
C33
C33
C33
-C270
-C290
-C310
1264.5
1284.5
1304.5
1270
1290
1310
1277.5
1297.5
1317.5
-C330
-C350
-C370
1324.5
1344.5
1364.5
1337.5
1357.5
1377.5
CWDM*: 6 Wavelengths from 1270 nm to 1370 nm, each step 20 nm.
**********************************************************************************************************************************************************************
OPTOWAY TECHNOLOGY INC. No.38, Kuang Fu S. Road, Hu Kou, Hsin Chu Industrial Park, Hsin Chu, Taiwan 303
Tel: 886-3-5979798
Fax: 886-3-5979737
E-mail: sales@optoway.com.tw http: // www.optoway.com.tw 11/1/2008 V2.0