Approval sheet
REQUIREMENT
TEST AND REQUIREMENTS ( AEC Q200 )
TEST
PROCEDURE
Temperature Coefficient of Natural resistance change per change in degree centigrade.
Refer to
Resistance(T.C.R)
“QUICK REFERENCE DATA”
R2 R
106
1
(ppm/C) t1 : 20°C+5°C-1°C
Clause 4.8
R
1t2 t1
R1 : Resistance at reference temperature
R2 : Resistance at test temperature
High Temperature
Exposure (Storage)
Test 1000 hrs./ @T=170℃/ Un-powered.
Measurement at 24±2 hours after test conclusion.
△R/R max. ±(1%+0.5mΩ)
no visible damage
MIL-STD-202 Method 108
Temperature cycling
Test 1000 cycles (-55℃ to +125℃).
no visible damage
JESD22 Method JA-104
Moisture Resistance
Measurement at 24±2 hours after test conclusion
Test 65℃/ 80~100%RH/ 10Cycles(t=24hrs/cycle).
R/R max. ±(0.5%+1m)
no visible damage
MIL-STD-202 Method 106 Measurement at 24±2 hours after test conclusion.
Bias Humidity Test 1000 hours/ @85℃/85% RH./ 10% of operation power.
MIL-STD-202 Method 103 Measurement at 24±2 hours after test conclusion.
Operation life Test 1000 hrs./ TA=125℃ / 35% of operating power.
MIL-STD-202 Method 108 Measurement at 24±2 hours after test conclusion
R/R max. ±(0.5%+0.5m)
no visible damage
R/R max. ±(1%+0.5m)
no visible damage
R/R max. ±(1%+0.5m)
no visible damage
External Visual
Inspect device construction, marking and workmanship
MIL-STD-883 Method 2009
Physical Dimensions
JESD22 Method JB-100
Mechanical Shock
The chip dimension (L, W, T, D) prescribed in the detail specification shall Within the specified tolerance
be checked by Protech 2.5D.
Test Peak value:100g's / Wave:Hail-sine / Duration:6ms /
Velocity:12.3ft/sec.
Within product specification
tolerance and no visible
damage
MIL-STD-202 Method 213
Vibration
Test 5g’s for 20min., 12 cycles each of 3 orientations.
no visible damage
MIL-STD-202 Method 204
R/R max. ±(0.5%+0.5m)
no visible damage
Resistance to soldering heat Solder dipping @ 270℃±5℃ for 10sec.±1sec.
(R.S.H)
R/R max. ±(0.5%+0.5m)
MIL-STD-202 Method 210
Thermal Shock
MIL-STD-202 Method 107
ESD
Test –55 to 155 ℃ / dwell time 15min/ Max transfer time 20sec/ no visible damage
300cycles.
R/R max. ±(0.5%+0.5m)
no visible damage
Test contact 1KV (Min)
AEC-Q200-002
Solderability
R/R max. ±(1%+0.5m)
a) Bake the sample for 155℃ dwell time 4hrs/ solder dipping 235℃/ 5sec. good tinning (>95% covered)
J-STD-002
b) Steam the sample dwell time 8 hour/ solder dipping 215℃/ 5sec.
c) Steam the sample dwell time 8 hour/ solder dipping 260℃/ 7sec.
Bending 2mm
no visible damage
Board Flex
no visible damage
AEC-Q200-005
Terminal Strength
AEC-Q200-006
R/R max. ±(0.5%+1m)
Force: 1.8kg for 60sec.
No cracking or no part being
sheared off from its pad.
Short time overload
5×Rated power for 5 seconds.
no visible damage
(S.T.O.L) Clause 4.13
R/R max.±1%
Page 6 of 7
ASC_WW12J_J_AUTO_V02
Jul - 2023