5秒后页面跳转
WQCW1608Z0J12NPB PDF预览

WQCW1608Z0J12NPB

更新时间: 2024-10-29 16:59:23
品牌 Logo 应用领域
华新科技 - WALSIN /
页数 文件大小 规格书
7页 240K
描述
SMD Wire Wound Ceramic Chip RF Inductor(AEC-Q200) / WQCW Series 12, 35, 700mA

WQCW1608Z0J12NPB 数据手册

 浏览型号WQCW1608Z0J12NPB的Datasheet PDF文件第1页浏览型号WQCW1608Z0J12NPB的Datasheet PDF文件第2页浏览型号WQCW1608Z0J12NPB的Datasheet PDF文件第3页浏览型号WQCW1608Z0J12NPB的Datasheet PDF文件第4页浏览型号WQCW1608Z0J12NPB的Datasheet PDF文件第6页浏览型号WQCW1608Z0J12NPB的Datasheet PDF文件第7页 
RELIABILITY PERFORMANCE  
No.  
1
Item  
Test condition  
Requirements  
High  
1000 hrs. at rated operating temperature (e.g. 125°C part  
can be stored for 1000 hrs. @ 125°C. Same applies fo r  
105°C and 85°C. Unpowered.  
Measurement at 24±4 hours after test conclusion.  
1000 cycles (-40°C to +125°C). Note: If 85°C part o r  
105°C part the 1000 cycles will be at that temperat ure.  
Measurement at 24±4 hours after test conclusion. 30min  
maximum dwell time at each temperature extreme. 1 min.  
maximum transition time.  
Temperature  
Exposure  
(Storage)  
MIL-STD-202 Method 108  
Temperature  
Cycle  
JESD22  
Method JA-104  
2
1000 hours 85°C/85%RH. Unpowered.  
Biased Humidity  
Operation Life  
MIL-STD-202 Method 103  
MIL-PRF-27  
3
4
Measurement at 24±4 hours after test conclusion.  
1000 hrs. @ 105°C. If 85°C or 125°C part will be te sted at  
that temperature.  
Measurement at 24±4 hours after test conclusion.  
Method 213. Condition C,  
Peak Value: 100g’s, Duration: 6ms, Waveform: Half-sine  
Velocity Change: 12.3ft/sec  
Mechanical  
Shock  
MIL-STD-202 Method 213  
MIL-STD-202 Method 204  
MIL-STD-202 Method 210  
5
6
5g's for 20 minutes, 12 cycles each of 3 orientations.  
Note: Use 8"X5" PCB, .031" thick, 7 secure points on one  
long side and 2 secure points at corners of opposite sides.  
Parts mounted within 2" from any secure point. Test from  
10-2000 Hz.  
Condition B No pre-heat of samples. Note: Single Wave  
Solder - Procedure 2 for SMD and Procedure 1 for Leaded  
with solder within 1.5mm of device body.  
Vibration  
Resistance to  
Solder Heat  
7
8
Passive Component Human Body Model (HBM)  
Electrostatic Discharge (ESD) Test.  
Only direct contact discharge, record the voltage value  
what the sample can pass.  
AEC-Q200-002  
Or  
ISO/DIS10605  
ESD  
For both Leaded & SMD. Electrical Test not required.  
Magnification 50X. Conditions:  
Leaded: Method A @ 235°C, category 3. SMD:  
a) Method B, 4 hrs @ 155°C dry heat @ 235°C  
b) Method B @ 215°C category 3.  
Solderability  
J-STD-002  
UL-94  
9
c) Method D category 3 @ 260°C.  
Flammability  
Board Flex  
V-0 or V-1 Acceptable  
10  
60 sec minimum holding time.  
Force of 900g for 60 seconds.  
AEC-Q200-005  
AEC-Q200-006  
11  
12  
Terminal Strength  
(SMD)  
Page 5 of 7  
ASC_WQCW1608 Series_Auto  
Nov. 2018  

与WQCW1608Z0J12NPB相关器件

型号 品牌 获取价格 描述 数据表
WQCW1608Z0J14NPB WALSIN

获取价格

SMD Wire Wound Ceramic Chip RF Inductor(AEC-Q200) / WQCW Series 14, 35, 700mA
WQCW1608Z0J15NPB WALSIN

获取价格

SMD Wire Wound Ceramic Chip RF Inductor(AEC-Q200) / WQCW Series 15, 35, 700mA
WQCW1608Z0J16NPB WALSIN

获取价格

SMD Wire Wound Ceramic Chip RF Inductor(AEC-Q200) / WQCW Series 16, 34, 700mA
WQCW1608Z0J18NPB WALSIN

获取价格

SMD Wire Wound Ceramic Chip RF Inductor(AEC-Q200) / WQCW Series 18, 35, 700mA
WQCW1608Z0J1N6PB WALSIN

获取价格

SMD Wire Wound Ceramic Chip RF Inductor(AEC-Q200) / WQCW Series 1.6, 24, 700mA
WQCW1608Z0J1N8PB WALSIN

获取价格

SMD Wire Wound Ceramic Chip RF Inductor(AEC-Q200) / WQCW Series 1.8, 16, 700mA
WQCW1608Z0J20NPB WALSIN

获取价格

SMD Wire Wound Ceramic Chip RF Inductor(AEC-Q200) / WQCW Series 20, 40, 700mA
WQCW1608Z0J22NPB WALSIN

获取价格

SMD Wire Wound Ceramic Chip RF Inductor(AEC-Q200) / WQCW Series 22, 38, 700mA
WQCW1608Z0J23NPB WALSIN

获取价格

SMD Wire Wound Ceramic Chip RF Inductor(AEC-Q200) / WQCW Series 23, 38, 700mA
WQCW1608Z0J24NPB WALSIN

获取价格

SMD Wire Wound Ceramic Chip RF Inductor(AEC-Q200) / WQCW Series 24, 37, 700mA