THE CONNOR-WINFIELD CORP.
2111 COMPREHENSIVE DRIVE.
AURORA, IL 60505.
FAX (630) 851-5040.
PHONE (630) 851-4722.
www.conwin.com
P R O D UC T D ATA S H E E T
CRYSTAL CONTROLLED OSCILLATORS
CW 0509
VPLD51TE
106.25M
3.3V SURFACE MOUNT VCXO OSCILLATOR
ABSOLUTE MAXIMUM RATINGS
PARAMETER
TABLE 1.0
NOTE
UNITS
MINIMUM NOMINAL MAXIMUM
UNITS
°C
Storage Temperature
Supply Voltage
-40
-0.5
-0.5
-
-
-
85
7.0
7.0
VPLD51TE
(Vcc)
(Vc)
Vdc
Vdc
Control Voltage
DESCRIPTION
OPERATING SPECIFICATIONS
PARAMETER
TABLE 2.0
NOTE
MINIMUM NOMINAL MAXIMUM
UNITS
MHz
The Connor-Winfield
Center Frequency
(Fo)
16.384
-
275
Total Frequency Tolerance
Operating Temperature Range
Supply Voltage
-25
-
-
25
ppm
1
VPLD51TE is a 3.3V Voltage
Controlled Crystal Oscillator
(VCXO) with LVPECL
Differential outputs. The
VPLD51TE is designed for
use with PLL systems in
SONET/SDH systems
requiring low jitter and tight
stability.
0
70
°C
(Vcc)
(Icc)
3.135
3.3
-
3.465
Vdc
Supply Current
-
-
-
-
-
-
-
100
mA
Jitter (BW=10Hz to 20MHz)
Jitter (BW=12kHz to 80MHz)
SSB Phase Noise at 100Hz offset
SSB Phase Noise at 1KHz offset
SSB Phase Noise at 10KHz offset
SSB Phase Noise at 100KHz offset
-
5
1
-
ps rms
ps rms
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
-
-60
-90
-130
-135
-
-
-
INPUT CHARACTERISTICS
PARAMETER
TABLE 3.0
NOTE
MINIMUM NOMINAL MAXIMUM
UNITS
Vdc
ppm
%
Control Voltage Range
Absolute Pull Range (APR)
Monotonic Linearity
(Vc)
0.3
+/-25
-10
-
1.65
3.0
-
-
2
FEATURES
-
10
Input Impedance
50K
-
Ohm
KHz
Vdc
Vdc
3.3V OPERATION
-
-
-
Modulation Bandwidth (3dB)
Enable Input Voltage (Low)
Disable Input Voltage (High)
10
-
1.68
-
(Vil)
-
3
3
LVPECL DIFFERENTIALOUTPUTS
ENABLE / DISABLE FUNCTION
LOW JITTER <1pS RMS
(Vih)
2.275
LOW VOLTAGE PECL OUTPUT CHARACTERISTICS
TABLE 4.0
PARAMETER
MINIMUM NOMINAL MAXIMUM
UNITS
Ohms
Vdc
NOTE
LOAD
-
2.275
-
-
-
50
-
4
FREQUENCY TOLERANCE: ±25ppm
TEMPERATURE RANGE: 0 to 70°C
SURFACE MOUNT PACKAGE
TAPEAND REEL PACKAGING
Voltage
(High)
(Low)
(Voh)
(Vol)
-
1.68
55
Vdc
Duty Cycle at 50% Level
45
50
%
PACKAGE CHARACTERISTICS
TABLE 5.0
Package
Non-hermetic package consisting of an FR4 substrate with grounded metal
cover.
PROCESS RECOMMENDATIONS
Solder Reflow
TABLE 6.0
The component solder used internal to this device has a melting point of
221°C. The peak temperature inside the device should be less than or equal
to 220°C for a maximum of 10 seconds
ORDERING INFORMATION
Wash
Notes
Ultrasonic cleaning is not recommended.
VPLD51TE - 106.25MHz
1.0
Inclusive of calibration @ 25°C, frequency stability vs. temperature, supply and load variations, shock, vibration and aging
for ten years. Control voltage (Vc) = 1.65 Vdc.
VCXO
CENTER
FREQUENCY
2.0
3.0
4.0
Control voltage for (Fo) = 1.65 Vdc Typical. Positive Transfer Function.
When oscillator is disabled the true output is in a low state (Vol) and the complementary output is in the high state (VoH)
50 ohm termination into Vcc-2V or Thevein equivalent.
SERIES
Specifications subject to change without notice.
03/02/05
Vx503
1
2
01
REV:
Copyright 2001 Connor-Winfield all rights reserved.
DATASHEET #:
PAGE
OF
DATE:
a