VJ C0G (NP0) Dielectric
Vishay Vitramon
Surface Mount Multilayer Ceramic Chip Capacitors
for Commercial Applications
FEATURES
• C0G is an ultra-stable dielectric offering a
Temperature Coefficient of Capacitance (TCC)
of 0 30 ppm/°C
RoHS
COMPLIANT
• Low Dissipation Factor (DF)
• Ideal for critical timing and tuning applications
• Ideal for snubber and surge suppression applications
• Protective surface coating of high voltage capacitors
maybe required to prevent surface arcing.
• Surface mount, precious metal technology, wet build
process
ELECTRICAL SPECIFICATIONS
Note: Electrical characteristics at + 25 °C unless otherwise specified
Insulation Resistance (IR):
At + 25 °C and rated voltage 100 000 MΩ minimum or
1000 ΩF, whichever is less
At + 125 °C and rated voltage 10 000 MΩ minimum or
100 ΩF, whichever is less
Operating Temperature: - 55 °C to + 125 °C
Capacitance Range: 1.0 pF to 0.056 µF
Voltage Rating: 10 Vdc to 1000 Vdc
Dielectric Withstanding Voltage (DWV):
This is the maximum voltage the capacitors are tested for
a 1 to 5 second period and the charge/discharge current
does not exceed 50 mA
≤ 200 Vdc : DWV at 250 % of rated voltage
500 Vdc: DWV at 200 % of rated voltage
Temperature Coefficient of Capacitance (TCC):
0
30 ppm/°C from - 55 °C to + 125 °C
Dissipation Factor (DF):
0.1 % maximum at 1.0 Vrms and 1 kHz for values > 1000 pF
0.1 % maximum at 1.0 Vrms and 1 MHz for values ≤ 1000 pF
630/1000 Vdc: DWV at 150 % of rated voltage
Aging Rate: 0 % maximum per decade
ORDERING INFORMATION
VJ0805
A
102
K
X
A
A
T
### (2)
CASE
CODE
CAPACITANCE
NOMINAL CODE
CAPACITANCE
TOLERANCE
DC VOLTAGE
RATING (1)
PROCESS
CODE
DIELECTRIC
TERMINATION
MARKING
PACKAGING
0402
0603
0805
1206
1210
1808
1812
1825
2220
2225
A = C0G (NP0) Expressed in
picofarads (pF).
The first two
B = 0.10 pF
C = 0.25 pF
D = 0.5 pF
F = 1 %
G = 2 %
J = 5 %
K = 10 %
Note:
B, C, D < 10 pF
F, G, J, K ≥ 10 pF
X = Ni barrier
100 % tin
plated
X = 25 V
A = 50 V
A = Unmarked
M = Marked
Note: Marking is
only available for
0805 and 1206
B = 100 V
C = 200 V
E = 500 V
L = 630 V
G = 1000 V
digits are
significant, the
third is a
multiplier. An “R”
indicates a
decimal point.
Examples:
F = AgPd
102 = 1000 pF
1R8 = 1.8 pF
T = 7" reel/plastic tape
C = 7" reel/paper tape
R = 11 1/4" reel/plastic tape
P = 11 1/4" reel/paper tape
O = 7" reel/flamed paper tape
I = 11 1/4"/13" reel/flamed paper tape
Note: “I” and “O” is used for
“F” termination paper taped
Notes:
(1) DC voltage rating should not be exceeded in application
(2) Process Code may be added with up to three digits, used to control non-standard products and/or special requirements
(3) Case size designator may be replaced by a four digit drawing number used to control non-standard products and/or requirements
www.vishay.com
38
For technical questions, contact: mlcc@vishay.com
Document Number: 45053
Revision: 28-Aug-08