ALUMINUMꢀꢀELECTROLYTICꢀꢀCAPACITORS
4.5mmL Chip Type, Bi-Polarized
ZPseries
Chip type with 4.5mm height.
WP
Designed for surface mounting on high density PC board.
Applicable to automatic mounting machine fed with carrier tape.
Compliant to the RoHS directive (2011/65/EU).
Smaller
Products which are scheduled to be discontinued.
Not recommended for new designs
ZP
Smaller
Specifications
ZE
Item
Performance Characteristics
Category Temperature Range
Rated Voltage Range
Rated Capacitance Range
Capacitance Tolerance
Leakage Current
–40 to +85°C
6.3 to 50V
0.1 to 47µF
20% at 120Hz, 20°C
After 2 minutes' application of rated voltage leakage current is not more than 0.05 CV or 10 (µA) , whichever is greater.
,
Measurement frequency : 120Hz at 20°C
6.3
Rated voltage (V)
10
16
25
35
50
Tangent of loss angle (tan δ)
0.30
tan δ (MAX.)
0.24
0.20
0.18
0.16
0.16
Measurement frequency : 120Hz
Rated voltage (V)
6.3
4
10
3
16
2
25
2
35
2
50
2
Stability at Low Temperature
Z–25°C / Z+20°C
Z–40°C / Z+20°C
Impedance ratio
ZT / Z20 (MAX.)
8
8
4
4
3
3
The specifications listed at right shall be met when
the capacitors are restored to 20°C after the rated
voltage is applied for 2000 hours at 85°C with the
polarity inverted every 250 hours.
Capacitance change
tan δ
Within 20% of the initial capacitance value
300% or less than the initial specified value
Less than or equal to the initial specified value
Endurance
Shelf Life
Leakage current
After storing the capacitors under no load at 85°C for 1000 hours and then performing voltage treatment based on JIS C 5101-4
clause 4.1 at 20°C, they shall meet the specified values for the endurance characteristics listed above.
The capacitors are kept on a hot plate for 30 seconds, which is
Capacitance change Within 10% of the initial capacitance value
Resistance to soldering
heat
maintained at 250°C. The capacitors shall meet the
Less than or equal to the initial specified value
Less than or equal to the initial specified value
tan δ
characteristic requirements listed at right when they are
removed from the plate and restored to 20°C.
Leakage current
Marking
Black print on the case top.
Chip Type
Type numbering system (Example : 16V 10 F)
µ
1
2
3
4
5
6
7
8
9 10 11 12 13 14
U Z P 1 C 1 0 0 M C L 1 G B
Plastic platform
Capacitance
0.3 MAX.
C
0.2
Voltage
Lot No.
Taping code
Configuration
(mm)
6.3
1.8 2.1 2.4
4.3 5.3 6.6
4.3 5.3 6.6
1.0 1.3 2.2
φD
A
B
4
5
Capacitance tolerance ( 20ꢀ)
Rated capacitance (10µF)
Rated voltage (16V)
Series name
C
E
+0.1
–0.2
4.5
0.5 to 0.8
Voltage mark for 6.3V is 6V
.
Type
Dimensions
6.3
10
16
25
35
50
V
Cap. (µF)
0J
1A
1C
1E
1V
1H
Code
0R1
ꢀ
ꢀꢀꢀꢀ0.1
ꢀꢀꢀꢀ0.22
ꢀꢀꢀꢀ0.33
ꢀꢀꢀꢀ0.47
ꢀꢀꢀꢀ1
4
4
4
4
4
5
5
6.3
1.0
2.0
2.8
4.0
8.4
13
17
20
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
R22
R33
R47
010
2R2
3R3
4R7
100
220
330
470
ꢀꢀꢀꢀ2.2
ꢀꢀꢀꢀ3.3
ꢀꢀꢀꢀ4.7
ꢀꢀ10
4
5
5
6.3
8.4
16
18
29
5
5
6.3
12
16
27
4
5
6.3
6.3
12
23
37
49
4
6.3
6.3
17
33
41
ꢀꢀ22
ꢀꢀ33
5
6.3
6.3
28
37
45
Case size
φ D (mm)
Rated
ripple
ꢀꢀ47
Rated ripple current (mArms) at 85°C 120Hz
Taping specifications are given in page 23.
Recommended land size, soldering by reflow are given
in page 18, 19.
Frequency coefficient of rated ripple current
Frequency
50 Hz
120 Hz
300 Hz
1 kHz
10 kHz or more
Coefficient
0.70
1.00
1.17
1.36
1.50ꢀꢀ
Please select WP(p.116), UN(p.162) series if high C/V
products are reqired.
Please refer to page 3 for the minimum order quantity.
CAT.8100D