ALUMINUM ELECTROLYTIC CAPACITORS
5.5mmL Chip Type, Bi-Polarized
WP series
Designed for surface mounting on high density PC board.
Applicable to automatic mounting machine using carrier tape.
Adapted to the RoHS directive (2002/95/EC).
WP
Smaller
ZP
Specifications
Item
Performance Characteristics
Temperature Range
Category
–40 ~ +85°C
Rated Voltage Range
Rated Capacitance Range
Capacitance Tolerance
Leakage Current
6.3 ~ 50V
0.1 ~ 100µF
±20% at 120Hz, 20°C
After 2 minutes' application of rated voltage, leakage current is not more than 0.05CV or 10 (µA) ,whichever is greater.
Measurement frequency : 120Hz, Temperature : 20°C
Rated voltage (V)
6.3
10
16
25
35
50
tan
δ
tan δ (MAX.)
0.24
0.20
0.17
0.17
0.15
0.15
Measurement frequency : 120Hz
Rated voltage (V)
6.3
4
8
10
3
6
16
2
4
25
2
4
35
2
3
50
2
3
Stability at Low Temperature
Z–25°C / Z+20°C
Z–40°C / Z+20°C
Impedance ratio
ZT / Z20 (MAX.)
After 1000 hours' application of rated voltage
at 85°C with the polarity inverted every 250
hours, capacitors meet the characteristic
requirements listed at right.
Capacitance change
tan δ
Within ±20% of initial value
200% or less of initial specified value
Initial specified value or less
Endurance
Shelf Life
Leakage current
After storing the capacitors under no load at 85°C for 1000 hours, and after performing voltage treatment based on JIS C 5101-4
clause 4.1 at 20°C, they will meet the specified value for characteristics listed above.
endurance
The capacitors shall be kept on the hot plate maintained at 250°C
for 30 seconds. After removing from the hot plate and restored
at room temperature, they meet the characteristic requirements
listed at right.
Capacitance change
tan δ
Within ±10% of initial value
Initial specified value or less
Initial specified value or less
Resistance to soldering
heat
Leakage current
Marking
Black print on the case top.
Type numbering system (Example : 16V 10 F)
µ
Chip Type
Capacitance
1
2
3
4
5
6
7
8
9 10 11 12 13 14
Plastic platform
0.3 MAX.
C±0.2
Voltage
Lot No.
U W P 1 C 1 0 0 M C L 1 G B
Taping code
Configuration
Capacitance tolerance (±20%)
Rated Capacitance (10µF)
Rated voltage (16V)
Series name
+0.1
–0.2
(mm)
8
5.4
φD
4
5
6.3
Voltage mark for 6.3V is 6V
.
0.5 ~ 0.8
A
B
C
E
1.8 2.1 2.4 3.3
4.3 5.3 6.6 8.3
4.3 5.3 6.6 8.3
1.0 1.3 2.2 2.3
Type
Dimensions
V
6.3
0J
10
16
25
35
50
Cap. (µF)
0.1
Code
0R1
R22
R33
R47
010
2R2
3R3
4R7
100
220
330
470
101
1A
1C
1E
1V
1H
4
1.0
2.0
2.8
4.0
8.4
0.22
0.33
0.47
1
4
4
4
4
2.2
3.3
4.7
4
8.4
16
5
13
5
12
16
27
50
61
5
5
17
20
36
4
12
23
5
5
18
29
54
6.3
8
10
4
17
33
41
61
5
6.3
8
6.3
8
22
33
5
28
37
45
82
6.3
6.3
8
6.3
6.3
8
37
49
75
6.3
6.3
8
8
Allowable
47
ripple
Rated
Case size
φ D (mm)
ripple
100
Rated Ripple (mArms) at 85°C 120Hz
Frequency coefficient of rated ripple current
Taping specifications are given in page 24.
Recommended land size, soldering by reflow are given
in page 25, 26.
Frequency
50 Hz
120 Hz
300 Hz
1 kHz
10 kHz~
1.50
Coefficient
0.70
1.00
1.17
1.36
Please select UN(p.77) series if high C/V products are
reqired.
Please refer to page 3 for the minimum order quantity.
CAT.8100V