ALUMINUM ELECTROLYTIC CAPACITORS
5.5mmL Chip Type, Bi-Polarized
UWP
Designed for surface mounting on high density PC board.
Applicable to automatic mounting machine fed with carrier tape.
Compliant to the RoHS directive (2011/65/EU).
Bi-polarized
UWX
UWP
Specifications
Item
Performance Characteristics
Category Temperature Range
Rated Voltage Range
Rated Capacitance Range
Capacitance Tolerance
Leakage Current
–40 to +85°C
6.3 to 50V
0.1 to 100µF
20% at 120Hz, 20°C
After 2 minutes' application of rated voltage at 20°C, leakage current is not more than 0.05CV or 10 (µA) ,whichever is greater.
Measurement frequency : 120Hz at 20°C
Rated voltage (V)
6.3
10
16
25
35
50
Tangent of loss angle (tan δ)
tan δ (MAX.)
0.24
0.20
0.17
0.17
0.15
0.15
Measurement frequency : 120Hz
Rated voltage (V)
6.3
4
8
10
3
6
16
2
4
25
2
4
35
2
3
50
2
3
Stability at Low Temperature
Z–25°C / Z+20°C
Z–40°C / Z+20°C
Impedance ratio
ZT / Z20 (MAX.)
The specifications listed at right shall be met
when the capacitors are restored to 20°C after the
rated voltage is applied for 1000 hours at 85°C
with the polarity inverted every 250 hours.
Capacitance change
tan δ
Within 20% of the initial capacitance value
200% or less than the initial specified value
Less than or equal to the initial specified value
Endurance
Shelf Life
Leakage current
After storing the capacitors under no load at 85°C for 1000 hours and then performing voltage treatment based on JIS C 5101-4
clause 4.1 at 20°C, they shall meet the specified values for the
characteristics listed above.
endurance
The capacitors are kept on a hot plate for 30 seconds, which
is maintained at 250°C. The capacitors shall meet the
characteristic requirements listed at right when they are
removed from the plate and restored to 20°C.
Within 10% of the initial capacitance value
Less than or equal to the initial specified value
Less than or equal to the initial specified value
Capacitance change
Resistance to soldering
heat
tan δ
Leakage current
Marking
Black print on the case top.
Chip Type
Capacitance
Type numbering system (Example : 16V 10 F)
µ
1
2
3
4
5
6
7
8
9 10 11 12 13 14
Plastic platform
0.3 MAX.
C
0.2
Voltage
Lot No.
U W P 1 C 1 0 0 M C L 1 G B
Taping code
Configuration
Capacitance tolerance ( 20ꢀ)
Rated capacitance (10µF)
Rated voltage (16V)
Series name
+0.1
–0.2
0.5 to 0.8
(mm)
8
5.4
φD
4
5
6.3
Voltage mark for 6.3V is 6V
.
A
B
C
E
1.8 2.1 2.4 3.3
4.3 5.3 6.6 8.3
4.3 5.3 6.6 8.3
1.0 1.3 2.2 2.3
Type
Dimensions
V
6.3
10
16
25
35
50
Cap. (µF)
0.1
Code
0R1
R22
R33
R47
010
2R2
3R3
4R7
100
220
330
470
101
0J
1A
1C
1E
1V
1H
4
4
4
4
4
5
5
6.3
8
1.0
2.0
2.8
4.0
8.4
0.22
0.33
0.47
1
2.2
3.3
4.7
10
22
33
4
5
5
6.3
8
8.4
16
18
29
54
13
5
5
6.3
8
8
12
16
27
50
61
17
20
36
4
5
6.3
6.3
8
12
4
17
33
41
61
23
37
49
75
5
28
37
45
82
6.3
6.3
8
6.3
6.3
8
Allowable
47
100
ripple
Rated
ripple
Case size
φ D(mm)
Rated ripple current (mArms) at 85°C 120Hz
Frequency coefficient of rated ripple current
Taping specifications are given in page 23.
Frequency
Recommended land size, soldering by reflow are given in page 18, 19.
Please select UUN(p.164) if high C/V products are reqired.
Please refer to page 3 for the minimum order quantity.
50 Hz
120 Hz
300 Hz
1 kHz
10 kHz or more
Coefficient
0.70
1.00
1.17
1.36
1.50ꢀꢀ
118