ALUMINUM ELECTROLYTIC CAPACITORS
6mmL Chip Type, Wide Temperature Range
UT series
Chip type with load life 2000 hours at +105°C
.
Designed for surface mounting on high density PC board.
Applicable to automatic mounting machine using carrier tape.
Adapted to the RoHS directive (2002/95/EC).
Long Life
UA
Long Life
WT
U T
Higher C/V
UX
Specifications
Item
Performance Characteristics
Category Temperature Range
Rated Voltage Range
Rated Capacitance Range
Capacitance Tolerance
Leakage Current
–55 ~ +105°C
4 ~ 50V
0.1 ~ 100µF
±20% at 120Hz, 20°C
After 2 minutes' application of rated voltage, leakage current is not more than 0.01 CV or 3 (µA) , whichever is greater.
Measurement frequency :120Hz, Temperature : 20°C
Rated voltage (V)
4
6.3
10
16
25
35
50
tan
δ
tan δ (MAX.)
0.37
0.28
0.24
0.20
0.16
0.13
0.12
Measurement frequency :120Hz
Rated voltage (V)
4
6
12
6.3
3
8
10
3
5
16
2
4
25
2
3
35
2
3
50
2
3
Stability at Low Temperature
Z–25°C / Z+20°C
Z–40°C / Z+20°C
Impedance ratio
ZT / Z20 (MAX.)
Capacitance
change
Within ±25% of initial value (16V or less)
Within ±20% of initial value (25V or more)
200% or less of initial specified value
Initial specified value or less
After 2000 hours' application of rated voltage
at 105°C , capacitors meet the characteristic
requirements listed at right.
Endurance
Shelf Life
tan δ
Leakage current
After storing the capacitors under no load at 105°C for 1000 hours, and after performing voltage treatment based on JIS C 5101-4
clause 4.1 at 20°C, they will meet the specified value for endurance characteristics listed above.
The capacitors shall be kept on the hot plate maintained at 250°C
Capacitance change
tan δ
Within ±10% of initial value
Initial specified value or less
Initial specified value or less
Resistance to soldering
heat
for 30 seconds. After removing from the hot plate and restored
at room temperature, they meet the characteristic requirements
listed at right.
Leakage current
Marking
Black print on the case top.
Type numbering system (Example : 16V 10 F)
µ
Chip Type
1
2
3
4
5
6
7
8
9 10 11 12 13 14
Positive
105°C Marking
U U T 1 C 1 0 0 M C L 1 G S
Capacitance
Plastic platform
Taping code
Lot No.
Voltage
0.3MAX.
C±0.2
(mm)
6.3
Configuration
φD
4
5
A
1.8 2.1 2.4
4.3 5.3 6.6
4.3 5.3 6.6
1.0 1.3 2.2
5.8 5.8 5.8
Capacitance tolerance (±20%)
B
C
E
L
Rated Capacitance (10µF)
Rated voltage (16V)
Series name
Negative
0.5 ~ 0.8
Type
L±0.3
Voltage mark for 6.3V is 6V
.
Dimensions
V
4
6.3
0J
10
16
1C
25
35
50
Code
0R1
R22
R33
R47
010
2R2
3R3
4R7
100
220
330
470
101
Cap.(µF)
0.1
0G
1A
1E
1V
1H
4
1.0
2.6
3.2
3.8
6.2
4
0.22
0.33
0.47
1
4
4
4
4
11
2.2
3.3
4.7
4
14
19
30
4
13
23
38
48
4
15
25
42
5
4
18
30
40
50
5
5
6.3
10
4
22
4
22
30
36
60
5
27
5
6.3
6.3
6.3
22
33
5
30
36
60
5
5
35
46
60
6.3
6.3
5
5
6.3
6.3
47
Allowable
Rated
Case size
φD (mm)
ripple
6.3
6.3
100
ripple
Rated Ripple (mArms) at 105°C 120Hz
Taping specifications are given in page 24.
Recommended land size, soldering by reflow are given in page 25, 26.
Please select UX(p.74), UJ(p.76) series if high C/V products are
required.
Frequency coefficient of rated ripple current
Frequency
50 Hz
120 Hz
300 Hz
1 kHz
10 kHz~
1.50
Coefficient
0.70
1.00
1.17
1.36
Please refer to page 3 for the minimum order quantity.
CAT.8100V