ALUMINUM ELECTROLYTIC CAPACITORS
6mmL Chip Type, Wide Temperature Range
UT series
Chip type with load life 2000 hours at +105°C
.
Designed for surface mounting on high density PC board.
Applicable to automatic mounting machine fed with carrier tape.
Compliant to the RoHS directive (2011/65/EU).
Long Life
UA
Long Life
WT
U T
Higher C/V
UX
Specifications
Item
Performance Characteristics
Category Temperature Range
Rated Voltage Range
Rated Capacitance Range
Capacitance Tolerance
Leakage Current
–55 to +105°C
4 to 50V
0.1 to 100µF
± 20% at 120Hz, 20°C
After 2 minutes' application of rated voltage, leakage current is not more than 0.01 CV or 3 (µA) , whichever is greater.
Measurement frequency :120Hz at 20°C
Rated voltage (V)
4
0.37
6.3
0.28
10
0.24
16
0.20
25
0.16
35
0.13
50
0.12
Tangent of loss angle (tan δ)
tan δ (MAX.)
Measurement frequency :120Hz
Rated voltage (V)
4
6
12
6.3
3
8
10
3
5
16
2
4
25
2
3
35
2
3
50
2
3
Stability at Low Temperature
Z–25°C / Z+20°C
Z–40°C / Z+20°C
Impedance ratio
ZT / Z20 (MAX.)
Capacitance
change
Within ±25% of the initial capacitance value (16V or less)
Within ±20% of the initial capacitance value (25V or more)
200% or less than the initial specified value
The specifications listed at right shall be met
when the capacitors are restored to 20°C after
the rated voltage is applied for 2000 hours at
105°C.
Endurance
Shelf Life
tan δ
Less than or equal to the initial specified value
Leakage current
After storing the capacitors under no load at 105°C for 1000 hours and then performing voltage treatment based on JIS C 5101-4
clause 4.1 at 20°C, they shall meet the specified values for the endurance characteristics listed above.
The capacitors are kept on a hot plate for 30 seconds, which is
Capacitance change
tan δ
Within ±10% of the initial capacitance value
Less than or equal to the initial specified value
Less than or equal to the initial specified value
Resistance to soldering
heat
maintained at 250°C. The capacitors shall meet the characteristic
requirements listed at right when they are removed from the plate
and restored to 20°C.
Leakage current
Marking
Black print on the case top.
Type numbering system (Example : 16V 10 F)
µ
Chip Type
1
2
3
4
5
6
7
8
9 10 11 12 13 14
Positive
105°C Marking
U U T 1 C 1 0 0 M C L 1 G S
Capacitance
Plastic platform
Taping code
Lot No.
Voltage
0.3MAX.
C±0.2
(mm)
6.3
Configuration
φD
4
5
A
1.8 2.1 2.4
Capacitance tolerance (±20%)
B
C
E
4.3 5.3 6.6
4.3 5.3 6.6
1.0 1.3 2.2
Rated capacitance (10µF)
Rated voltage (16V)
Series name
Negative
0.5 to 0.8
Type
5.8±0.3
Voltage mark for 6.3V is 6V
.
Dimensions
V
4
6.3
0J
10
16
1C
25
35
50
Code
0R1
R22
R33
R47
010
2R2
3R3
4R7
100
220
330
470
101
Cap.(µF)
0.1
0G
1A
1E
1V
1H
4
1.0
2.6
3.2
3.8
6.2
4
0.22
0.33
0.47
1
4
4
4
4
11
2.2
3.3
4.7
4
14
19
30
4
13
23
38
48
4
15
25
42
5
4
18
30
40
50
5
5
6.3
10
4
22
4
22
30
36
60
5
27
5
6.3
6.3
6.3
22
33
5
30
36
60
5
5
35
46
60
6.3
6.3
5
5
6.3
6.3
47
Allowable
Rated
Case size
φ D (mm)
ripple
6.3
6.3
100
ripple
Rated ripple current (mArms) at 105°C 120Hz
Taping specifications are given in page 23.
Recommended land size, soldering by reflow are given in page 18, 19.
Please select UX(p.158), UJ(p.164) series if high C/V products are
required.
Frequency coefficient of rated ripple current
Frequency
50 Hz
120 Hz
300 Hz
1 kHz 10 kHz or more
Coefficient
0.70
1.00
1.17
1.36 1.50
Please refer to page 3 for the minimum order quantity.
CAT.8100C