ALUMINUM ELECTROLYTIC CAPACITORS
6mmL Chip Type, Wide Temperature Range
UTseries
Chip type with load life 2000 hours at +105°C
.
Designed for surface mounting on high density PC board.
Applicable to automatic mounting machine using carrier tape.
Adapted to the RoHS directive (2002/95/EC).
Long Life
UA
Long Life
WT
UT
Higher C/V
UX
Specifications
Item
Performance Characteristics
Category Temperature Range
Rated Voltage Range
Rated Capacitance Range
Capacitance Tolerance
Leakage Current
–55 ~ +105°C
4 ~ 50V
0.1 ~ 100µF
± 20% at 120Hz, 20°C
After 2 minutes' application of rated voltage, leakage current is not more than 0.01 CV or 3 (µA) , whichever is greater.
Measurement frequency :120Hz, Temperature : 20°C
Rated voltage (V)
4
6.3
10
16
25
35
50
tan
δ
tan δ (MAX.)
0.37
0.28
0.24
0.20
0.16
0.13
0.12
Measurement frequency :120Hz
Rated voltage (V)
4
6
12
6.3
3
8
10
3
5
16
2
4
25
2
3
35
2
3
50
2
3
Stability at Low Temperature
Z–25°C / Z+20°C
Z–40°C / Z+20°C
Impedance ratio
ZT / Z20 (MAX.)
Capacitance
change
Within ±25% of initial value (16V or less)
Within ±20% of initial value (25V or more)
200% or less of initial specified value
Initial specified value or less
After 2000 hours' application of rated voltage
at 105°C , capacitors meet the characteristic
requirements listed at right.
Endurance
Shelf Life
tan δ
Leakage current
After leaving capacitors under no load at 105°C for 1000 hours,
they meet the specified value for endurance characteristics listed above.
The capacitors shall be kept on the hot plate maintained at 250°C
for 30 seconds. After removing from the hot plate and restored
at room temperature, they meet the characteristic requirements
listed at right.
Capacitance change
tan δ
Within ±10% of initial value
Initial specified value or less
Initial specified value or less
Resistance to soldering
heat
Leakage current
Marking
Black print on the case top.
Type numbering system (Example : 16V 10 F)
µ
Chip Type
1
2
3
4
5
6
7
8
9 10 11 12 13 14
Positive
105°C Marking
U U T 1 C 1 0 0 M C L 1 G S
Capacitance
Plastic platform
0.3MAX.
Voltage
Taping code
Lot No.
C±0.2
(mm)
6.3
Configuration
φD
4
5
A
1.8 2.1 2.4
4.3 5.3 6.6
4.3 5.3 6.6
1.0 1.3 2.2
5.8 5.8 5.8
Capacitance tolerance (±20%)
B
C
E
L
Rated Capacitance (10µF)
Rated voltage (16V)
Series name
Negative
0.5 ~ 0.8
Type
L±0.3
Voltage mark for 6.3V is 6V
.
Dimensions
V
4
6.3
0J
10
16
1C
25
35
50
Code
0R1
R22
R33
R47
010
2R2
3R3
4R7
100
220
330
470
101
Cap.(µF)
0.1
0G
1A
1E
1V
1H
4
1.0
2.6
3.2
3.8
6.2
0.22
0.33
0.47
1
4
4
4
4
2.2
3.3
4.7
4
11
4
14
19
30
4
13
23
38
48
4
15
25
42
5
10
4
18
30
40
50
5
5
6.3
22
33
4
22
30
36
60
4
22
30
36
60
5
27
5
6.3
6.3
6.3
5
5
5
35
46
60
6.3
6.3
47
5
5
6.3
6.3
Allowable
Rated
Case size
φD (mm)
ripple
100
6.3
6.3
ripple
Rated Ripple (mA rms) at 105°C 120Hz
Taping specifications are given in page 24.
Recommended land size, soldering by reflow are given in page 25
Please select UX(p.66), UJ(p.68) series if high C/V products are required.
Please refer to page 3 for the minimum order quantity.
Frequency coefficient of rated ripple current
Frequency
50 Hz
120 Hz
300 Hz
1 kHz
10 kHz~
1.50
Coefficient
0.70
1.00
1.17
1.36
CAT.8100U