ALUMINUM ELECTROLYTIC CAPACITORS
Low Impedance, For Switching Power Supplies
PJseries
Approved by Reliability Center for Electronic
Component, Japan-Certification No. RCJ-03-23C
Low impedance and high reliability withstanding 5000 hours load life
at +105˚C (3000 / 2000 hours for smaller case sizes as specified below).
Capacitance ranges available based on the numerical values in E12 series under JIS.
Ideally suited for use of switching power supplies.
Low Impedance
PS
High Ripple current
PJ
Specifications
Item
Performance Characteristics
Category Temperature Range
Rated Voltage Range
–55 ~ +105˚C (6.3 ~ 100V), –40 ~ +105˚C (160 ~ 400V), –25 ~ +105˚C (450V)
6.3 ~ 450V
Rated Capacitance Range
Capacitance Tolerance
0.47 ~ 15000µF
± 20% at 120Hz, 20˚C
Rated Voltage (V)
6.3 ~ 100
160 ~ 450
<
=
=
+
Leakage Current
After 1 minute's application of rated voltage, leakage current is not more
than 0.03CV or 4 (µA), whichever is greater.
CV 1000 :
=
0.1CV 40 (µA) max. (1 minute's)
I
I
Leakage current
>
+
CV 1000 :
0.04CV 100 (µA) max. (1 minute's)
For capacitance of more than 1000µF, add 0.02 for every increase of 1000µF.
Measurement frequency : 120Hz, Temperature : 20˚C
•
tan
δ
6.3
0.22
10
0.19
16
0.16
25
0.14
35
0.12
50
0.10
63 ~ 100 160 ~ 350 400 450
Rated Voltage (V)
tan MAX.
δ
(
)
0.08
0.20
0.25
•
•
Rated voltage (V)
120Hz
6.3 10
16
3
—
—
25 35 50 ~ 100 160 ~ 200 250
315 ~ 350
400
450
—
—
Z–55˚C / Z+20˚C
Z–40˚C / Z+20˚C
Z–25˚C / Z+20˚C
4
—
—
3
—
—
2
—
—
—
4
—
6
—
8
—
—
10
—
Impedance
ratio
Stability at Low Temperature
—
—
15
After an application of D.C. bias voltage plus the rated ripple
current for 5000 hours (2000 hours for D = 5 and 6.3, 3000
hours for D = 8 )at 105˚C the peak voltage shall not exceed the
rated D.C. voltage, capacitors meet the characteristic
requirements shown on the right.
Capacitance change Within ±20% of initial value
tan δ
200% or less of initial specified value
Initial specified value or less
Endurance
Leakage current
Capacitance change Within ±20% of initial value
After leaving capacitors under no load at 105˚C
for 1000 hours, they meet the characteristic
requirements listed at right.
tan δ
Shelf Life
Marking
150% or less of initial specified value
Initial specified value or less
Leakage current
Printed with white color letter on dark brown sleeve.
Type numbering system (Example : 25V 470µF)
Radial Lead Type
1
2
3
4
5
6
7
8
9 10 11 12
Sleeve
φ d
U P J 1 E 4 7 1 M H H 6
Case size code
Code
Configuration
Type
Capacitance tolerance (±20%)
Small Dia
φD
Code
DH
Low Profile
6
5
Rated Capacitance (470µF)
6.3
EH
Rated voltage (25V)
•
8
10
PH
Pressure
Series name 12.5 ~ 18 HH
relief vent
+
MAX
MIN
MIN
4
L
(φ6.3UP)
15
Type
The PET sleeve product is also available upon request.
•
In this case, T will be Rpuatteadtv1o1lttahgdeigit of type numbering sysFtreemqu.ency coefficient
15000
Rated voltage
Frequency coefficient
(φD < 10) 1.0
(φD 10) 1.5
Frequency coefficient of
rated ripple current
1001050000
681000000
6800
4700
4700
φD
P
5
6.3
2.5
0.5
8
10
5.0
0.6
12.5
5.0
16
18
7.5
0.8
3300
3300
2.0
0.5
3.5
0.6
7.5
0.8
2200
2200
φd
0.6
1500
1500
In case L >25 for the φ12.5 dia. unit, lead dia. φ d=0.8mm.
1000
1000
680
470
330
220
150
100
68
6.3 ~ 100V
(10kHz ~
200kHz = 1)
47
33
120Hz
300Hz
1kHz
22
15
10
0.68
0.47
0
0.5
0.6
0.7
0.8
0.9
1.0
Frequency coefficient
Please refer to page 18, 19, 20 about the formed or taped product spec.
Please refer to page 3 for the minimum order quantity.
50Hz
0.80
120Hz
1.00
300Hz
1.25
1kHz
1.40
10kHz~
1.60
160 ~ 450V
Dimension table in next page.
CAT.8100R