5秒后页面跳转
捷配首页

Datasheet > 电源电路 > 开关式稳压器或控制器> UCC2583QTR
UCC2583QTR PDF预览

UCC2583QTR

更新时间： 2024-11-30 12:01:43
品牌 Logo 应用领域
德州仪器 - TI 稳压器开关信息通信管理
页数 文件大小 规格书
18页 1097K
描述
Switch Mode Secondary Side Post Regulator

阅读下载

中文翻译

获取价格

UCC2583QTR 数据手册

 浏览型号UCC2583QTR的Datasheet PDF文件第2页浏览型号UCC2583QTR的Datasheet PDF文件第3页浏览型号UCC2583QTR的Datasheet PDF文件第4页浏览型号UCC2583QTR的Datasheet PDF文件第5页浏览型号UCC2583QTR的Datasheet PDF文件第6页浏览型号UCC2583QTR的Datasheet PDF文件第7页 
UCC1583  
UCC2583  
UCC3583  
Switch Mode Secondary Side Post Regulator  
FEATURES  
DESCRIPTION  
• Precision Secondary Side Post  
Regulation for Multiple Output Power  
Supplies  
The UCC3583 is a synchronizable secondary side post regulator for preci-  
sion regulation of the auxiliary outputs of multiple output power supplies. It  
contains a leading edge pulse width modulator, which generates the gate  
drive signal for a FET power switch connected in series with the rectifying  
diode. The turn-on of the power switch is delayed from the leading edge of  
the secondary power pulse to regulate the output voltage. The UCC3583  
contains a ramp generator slaved to the secondary power pulse, a voltage  
error amplifier, a current error amplifier, a PWM comparator and associ-  
ated logic, a gate driver, a precision reference, and protection circuitry.  
• Useful for Both Single Ended and  
Center Tapped Secondary Circuits  
• Ideal Replacement for Complex  
Magnetic Amplifier Regulated Circuits  
• Leading Edge Modulation  
The ramp discharge and termination of the gate drive signal are triggered  
by the synchronization pulse, typically derived from the falling edge of the  
transformer secondary voltage. The ramp starts charging again once its  
low threshold is reached. The gate drive signal is turned on when the ramp  
voltage exceeds the control voltage. This leading edge modulation tech-  
nique prevents instability when the UCC3583 is used in peak current mode  
primary controlled systems.  
• Does Not Require Gate Drive  
Transformer  
• High Frequency (>500kHz) Operation  
• Applicable for Wide Range of Output  
Voltages  
• High Current Gate Driver (0.5A  
The controller operates from a floating power supply referenced to the out-  
put voltage being controlled. It features an undervoltage lockout (UVLO)  
circuit, a soft start circuit, and an averaging current limit amplifier. The cur-  
rent limit can be programmed to be proportional to the output voltage, thus  
achieving foldback operation to minimize the dissipation under short circuit  
conditions.  
Sink/1.5A Source)  
• Average Current Limiting Loop  
(continued)  
TYPICAL APPLICATION AND BLOCK DIAGRAM  
UDG-96201-2  
Note: Pin connections shown for 14-pin packages.  
SLUS299B - OCTOBER 1998 - REVISED JANUARY 2005  
1234567...18

中文翻译

下载PDF

UCC2583QTR 替代型号

型号 品牌 替代类型 描述 数据表
UCC2583QG3 TI

完全替代

 1.8A SWITCHING CONTROLLER, 500kHz SWITCHING FREQ-MAX, PQCC20, GREEN, PLASTIC, LCC-20
UCC2583QTRG3 TI

类似代替

 Switch Mode Secondary Side Post Regulator

与UCC2583QTR相关器件

型号 品牌 获取价格 描述 数据表
UCC2583QTRG3 TI

获取价格

 		Switch Mode Secondary Side Post Regulator
UCC2585 TI

获取价格

 		Low Voltage Synchronous Buck Controller
UCC2585DG4 TI

获取价格

 		1A SWITCHING CONTROLLER, 500kHz SWITCHING FREQ-MAX, PDSO16, GREEN, PLASTIC, MS-012AC, SOIC
UCC2585DTR TI

获取价格

 		1A SWITCHING CONTROLLER, 500kHz SWITCHING FREQ-MAX, PDSO16, PLASTIC, MS-012AC, SOIC-16
UCC2585DTRG4 TI

获取价格

 		1A SWITCHING CONTROLLER, 500kHz SWITCHING FREQ-MAX, PDSO16, PLASTIC, SOIC-16
UCC2585J TI

获取价格

 		1A SWITCHING CONTROLLER, 700kHz SWITCHING FREQ-MAX, CDIP16, CERAMIC, DIP-16
UCC2585MG4 TI

获取价格

 		1A SWITCHING CONTROLLER, 500kHz SWITCHING FREQ-MAX, PDSO16, GREEN, PLASTIC, QSOP-16
UCC2585MTR TI

获取价格

 		暂无描述
UCC2585NG4 TI

获取价格

 		IC 1 A SWITCHING CONTROLLER, 500 kHz SWITCHING FREQ-MAX, PDIP16, MS-001BB, PLASTIC, DIP-16
UCC2588-1D TI

获取价格

 		1A SWITCHING CONTROLLER, 700kHz SWITCHING FREQ-MAX, PDSO16, SOIC-16

与UCC2583QTR相关文章

您还可以找


热门产品
PCB打样/小批量
铝基板
BOM智能配单
PCBA制造
钣金
精密CNC
模具注塑
薄膜开关
精选活动
PCBA打样特惠
四六层板品质升级
铝基板品质升级
一体化电子制造
DFM下载
服务支持
企业认证
产品展示
工厂展示
工艺能力
积分商城
关于捷配
捷配简介
企业文化
公司动态
人才招聘
联系我们
帮助中心
下单流程
付款流程
开票流程
常见问题
全球PCB制造服务专线 400-613-0088

工作时间：9:00-21:00

CEO邮箱：ceo@jiepei.com

投诉邮箱：tousu@jiepei.com

捷配网-微信公众号 微信公众号
捷配网-微信公众号 抖音公众号
资质认证：
合作快递：
支付方式：
Copyright © 2024 Jiepei.com Inc. All Rights Reserved. 版权所有:杭州捷配信息科技有限公司 浙公网安备 33010502006866号 浙ICP备10014259号-119 营业执照ICP证