ꢀꢁ ꢂ ꢃꢄ ꢅꢃ
ꢀꢁ ꢂ ꢃꢄ ꢅꢄ
www.ti.com
SLUS536C − AUGUST 2002 − REVISED AUGUST 2004
ꢆ ꢇ ꢈ ꢈ ꢉꢆ ꢊ ꢋꢀ ꢇꢌꢊ ꢍ ꢎ ꢏꢐꢉ ꢑ
ꢒ ꢓ ꢀ ꢂꢔꢋ ꢁ ꢁ ꢓꢔꢊ ꢌ ꢕ ꢋꢖ ꢋꢗ ꢊ ꢌ
FEATURES
DESCRIPTION
D
D
D
D
D
D
D
D
D
D
D
D
Wide Input Supply Range: −20 V to −80 V
The TPS2392 and TPS2393 integrated circuits are hot
swap power managers optimized for use in nominal
−48-V systems. They operate with supply voltage
ranges from −20-V to −80-V, and are rated to withstand
spikes to −100 V. In conjunction with an external
N-channel FET and sense resistor, they can be used to
enable live insertion of plug-in cards and modules in
powered systems. Each device provides load current
slew rate control and peak magnitude limiting.
Undervoltage and overvoltage shutdown thresholds
are easily programmed via a three-resistor divider
network. In addition, two active-low, debounced inputs
provide plug-in insertion detection. A power good (PG)
output enables downstream converters. The TPS2392
and TPS2393 also provide the basic hot swap functions
of electrical isolation of faulty cards, filtered protection
against nuisance overcurrent trips, and single-line fault
reporting. The 44-pin part supports designs where
telecomm creepage and clearance requirements must
be followed.
Transient Rating to −100 V
Programmable Current Limit
Programmable Current Slew Rate
Programmable UV/OV Thresholds/Hysteresis
Debounced Insertion Detection Inputs
Open-Drain Power Good (PG) Output
Fault Timer to Eliminate Nuisance Trips
Open-Drain Fault Output (FAULT)
Enable Input (EN)
14-Pin TSSOP package
44-Pin TSSOP Package for
Creapage/Clearance
APPLICATIONS
D
D
D
−48-V Distributed Power Systems
Central Office Switching
Wireless Base Station
The TPS2392 latches off in response to current faults,
while the TPS2393 periodically retries the load in the
event of a fault.
DC/DC
CONVERTER
VOUT+
R1
R2
200 kΩ
1%
4.99 kΩ
1%
VIN+
VOUT+
GND
V
DD
C4
100 µF
100 V
C
OUT
EN
R6
10 kΩ
R3
TPS2392/TPS2393
3.92 kΩ
1%
VIN−
VOUT−
1
2
3
4
5
6
7
UVLO
OVLO 14
VOUT−
D1
BAS19
R5
100
kΩ
INSA DRAINSNS 13
INSB
FAULT
EN
PG 12
RTN 11
D2
5.6 V
Q1
IRF530
= 32.8 V
V
C3
1500 pF
UV
GATE 10
FLTTIME ISENS
IRAMP −VIN
9
8
−48V
= 30.8 V
= 72.6 V
V
V
UV
OV
C2
0.1 µF
R4
20 mΩ
1/4, 1%
C1
3900 pF
UDG−02098
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments
semiconductor products and disclaimers thereto appears at the end of this data sheet.
.
ꢁꢌ ꢓ ꢍꢇ ꢘ ꢀꢙ ꢓ ꢖ ꢍ ꢋꢀꢋ ꢚꢛ ꢜꢝ ꢞ ꢟꢠ ꢡꢚꢝꢛ ꢚꢢ ꢣꢤ ꢞ ꢞ ꢥꢛꢡ ꢠꢢ ꢝꢜ ꢦꢤꢧ ꢨꢚꢣ ꢠꢡꢚ ꢝꢛ ꢩꢠ ꢡꢥꢪ ꢁꢞ ꢝꢩꢤ ꢣꢡꢢ
ꢣ ꢝꢛ ꢜꢝꢞ ꢟ ꢡꢝ ꢢ ꢦꢥ ꢣ ꢚ ꢜꢚ ꢣ ꢠ ꢡꢚ ꢝꢛꢢ ꢦ ꢥꢞ ꢡꢫꢥ ꢡꢥ ꢞ ꢟꢢ ꢝꢜ ꢀꢥꢬ ꢠꢢ ꢙꢛꢢ ꢡꢞ ꢤꢟ ꢥꢛꢡ ꢢ ꢢꢡ ꢠꢛꢩ ꢠꢞ ꢩ ꢭ ꢠꢞ ꢞ ꢠ ꢛꢡꢮꢪ
ꢁꢞ ꢝ ꢩꢤꢣ ꢡ ꢚꢝ ꢛ ꢦꢞ ꢝ ꢣ ꢥ ꢢ ꢢ ꢚꢛ ꢯ ꢩꢝ ꢥ ꢢ ꢛꢝꢡ ꢛꢥ ꢣꢥ ꢢꢢ ꢠꢞ ꢚꢨ ꢮ ꢚꢛꢣ ꢨꢤꢩ ꢥ ꢡꢥ ꢢꢡꢚ ꢛꢯ ꢝꢜ ꢠꢨ ꢨ ꢦꢠ ꢞ ꢠꢟ ꢥꢡꢥ ꢞ ꢢꢪ
Copyright 2004, Texas Instruments Incorporated