RESISTORSꢀCAPACITORSꢀCOILSꢀDELAY LINES
HIGH POWER PLANAR RESISTORS, 5W to 100W
Term.W is
RoHS
TP SERIESCERAMIC SUBSTRATE
TPS SERIES STEEL SUBSTRATE
compliant
& 260°C
RoHS
compatible
ꢀ Space saving flame retardant design
ꢀ High power density
ꢀ Thin profile, and lightweight
ꢀ Low Inductance: 50nh typ at 1MHz
ꢀ Wide resistance range: 0.5Ω to 1MΩ
ꢀ Excellent transient withstanding capabilities
ꢀ Standard tolerances: as tight as ±0.5%
SPACE SAVING THICK FILM PLANAR RESISTORS!
Series TP/TPS offer high power density in a lightweight design. Designed for
switch mode power supplies, snubber circuits, heaters, in-rush limiters,
dynamic braking, and other power applications, the planar construction offers
significant PCB real estate savings over conventional resistors, especially in
forced air applications. The unique design enables very low inductance and
excellent surge capabilities. Series TP utilize alumina substrates for excellent
heat dissipation. Series TPS utilize stainless steel substrates for even greater
dissipation and durability. A special hi-temp/hi-voltage dielectric insulates the
resistor and terminals from the metal substrate, enabling greater voltage and
insulation compared to porcelain enameled models.
OPTIONS
ꢀ Special marking, extended value range, custom
sizes and shapes, burn-in and military screening,
insulated leads, quick-disconnect terminals, multiple
resistor circuits, etc. Consult factory for assistance.
|
B
|
B
|
|
|
|
B
Series TP 15W-100W
4 Pins, Ceramic
Series TPS
Steel Substrate
50W - 100W 6 Pins
Series TP 5W - 10W
2 Pins, Ceramic
0.24±.01
[.61±.25]
A
A
A
→ ←
0.1
→
←
[2.54]
0.30 typ.
[7.6]
↓
↓
↑
.150 min
[3.8]
→ ←.04
0.120 [3]
min
.024 [.6] → ←
0.120 [3]
min
.02[.51] → ←
[1.02]
→ ←
.012 [.3]
.07[1.8]
.20”
C
D
.20”
.20”
.050”
Dia.
C
C
.04” Dia.
↑
→
←
.37[9.4]
.028”
Dia.
.20±.01
.20”
.20”
[5.08 ±.25]
.20”
Standard
DIMENSIONS Inch [mm]
RCD
Type
Wattage
@ 25°C
Max. Voltage
Rating1
Resistance
Range2
A Max
B Max
C
D
TP05
TP075
5W
7.5W
10W
15W
25W
50W
50W
100W
500V
500V
500V
500V
500V
500V
250V
300V
1Ω to 200K
1Ω to 200K
1Ω to 300K
1Ω to 1MΩ
1Ω to 1MΩ
1Ω to 1MΩ
0.5Ω to 10KΩ
0.5Ω to 20KΩ
1.015 [25.8]
1.015 [25.8]
1.015 [25.8]
1.22 [31]
.512 [13]
.200±.013 [5.08±.25]3
.500±.013,4 [12.7±.25]
.800±.013 [20.3±.25]
1.00±.02 [25.4±.5]
1.90±.02 [48.26±.5]
1.90±.02 [48.26±.5]
1.00±.02 [25.4±.5]
1.30±.02 [33.02±.5]
-
-
-
-
-
-
.765 [19.4]
TP10
1.015 [25.8]
1.27 [32.26]
2.22 [56.39]
2.22 [56.39]
1.77 [44.96]
2.59 [65.8]
TP155
TP255
TP505
TPS50
TPS100
1.18 [30]
2.27 [57.66]
2.80 [71.1]
3.65 [92.7]
1.40±.02 [35.56±.5]
1.70±.02 [43.18±.5]
1 Maximum Operating Voltage is DC or AC peak 2 Expanded range available 3 Available with 0.300” [7.62mm] pin spacing, specify opt.78 4 Available with 0.200” [5.08mm] pin spacing, specify opt.80
5 Preliminary information
TYPICAL PERFORMANCE CHARACTERISTICS
P/N DESIGNATION:
TP05
-
102 - J B W
Load Life (1000 hours)
±2%
RCD Type
Moisture Resistance
±1%
Options: assigned by RCD
(leave blank for standard)
Temperature Cycling
±1%
Resis.Code 0.5%, 1%: 3 signif. figures & multiplier,
e.g. 1R00=1Ω,10R0=10Ω,1000=100Ω,1001=1K, etc.
Resis.Code 2%-10%: 2 signif. figures & multiplier,
e.g. R50=.5Ω, 1R0=1Ω, 100=10Ω,101=100Ω,102=1K, etc.
Tol. Code: D=0.5%, F=1%, G=2%, J=5%, K=10%, M=20%
Packaging: B = Bulk
Overload (not to exceed max voltage)
Dielectric Strength
5x rated W, 200mS
500VDC (750V avail)
±0.5%
Resistance to Solder Heat (260°C, 5 sec)
Temperature Coefficient (ppm/°C)
100ppm°C (≥2%=200ppm)
TP = -55°C to 170°C
TPS = -55°C to 275°C
TP = 1%/°C > 70°C
Operating Temperature
Power Derating
Termination: W= Lead-free, Q= Tin/Lead
(leave blank if either is acceptable)
TPS = 0.4%/°C > 25°C
-
-
-
-
RCD Components Inc, 520 E.Industrial Park Dr, Manchester, NH, USA 03109 rcdcomponents.com Tel: 603 669 0054 Fax: 603 669 5455 Email:sales@rcdcomponents.com
FA048E Sale of this product is in accordance with GF-061. Specifications subject to change without notice.
68