TK111xxM
ABSOLUTE MAXIMUM RATINGS TK111xxMCL (VOUT ≥ 2.0 V)
Operating Temperature Range ...................-30 to +80 °C
Supply Voltage ......................................................... 16 V
Noise Bypass Terminal Voltage ................................. 5 V
Power Dissipation (Note 1) ................................ 600 mW
Reverse Bias............................................................ 10 V
Storage Temperature Range ................... -55 to +150 °C
Operating Voltage Range............................... 1.8 to 12 V
Junction Temperature ........................................... 150 °C
Lead Soldering Temperature (10 s) ...................... 235 °C
TK111xxMCL ELECTRICAL CHARACTERISTICS
Test conditions: VIN = VOUT(TYP) + 1 V, TA = 25 °C, unless otherwise specified.
SYMBOL
IQ
ISTBY
VOUT
PARAMETER
Quiescent Current
Standby Current
Output Voltage
TEST CONDITIONS
IOUT = 0 mA, Excluding ICONT
VIN = 6 V, Output OFF
MIN
TYP
MAX
200
0.1
UNITS
µA
140
µA
IOUT = 10 mA, VIN = VOUT(TYP) + 1 V
VIN = VOUT(TYP) + 1 V to
See Table 1
0.8
V
Line Reg Line Regulation
Load Reg Load Regulation
18
mV
V
OUT(TYP) + 6 V, (Note 2)
IOUT = 1 to 60 mA, (Note 2)
IOUT = 1 to 100 mA, (Note 2)
IOUT = 60 mA, (Note 2)
(Note 2)
8
30
55
mV
mV
mV
mA
14
VDROP
IOUT
Dropout Voltage
120
200
100
Continuous Output Current
5 ms pulse, 12.5 % duty cycle,
(Note 2)
IOUT(PULSE)
Pulse Output Current
130
mA
f = 1 kHz, CL = 4.7 µF,
CN = 0.1 µF, VIN = VOUT(TYP) + 2 V,
VR = 200 mVrms, IOUT = 10 mA,
(Notes 3,4)
RR
Ripple Rejection
70
30
dB
400 Hz ≤ f ≤ 80 kHz, CL = 4.7 µF,
CN = 0.01 µF, VIN = VOUT(TYP) + 2 V,
VNO
Output Noise Voltage
µVrms
IOUT = 10 mA, (Notes 3,4)
Noise Bypass Terminal
Voltage
Vref
1.25
25
V
∆VOUT /∆T
Temperature Coefficient
I
OUT = 10 mA
ppm/° C
CONTROL TERMINAL SPECIFICATIONS
ICONT
Control Current
VCONT = 1.8 V, Output ON
Output ON
1.2
4
µA
V
VCONT(ON)
Control Voltage ON
1.5
VCONT(OFF) Control Voltage OFF
Output OFF
0.35
V
Note 1: Power dissipation is 600 mW when mounted as recommended. Derate at 4.8 mW/°C for operation above 25 °C.
Note 2: Refer to “Definition of Terms.”
Note 3: Ripple rejection and noise voltage are affected by the value and characteristics of the capacitor used.
Note 4: Output noise voltage can be reduced by connecting a capacitor to the noise bypass terminal.
Gen. Note: Parameters with min. or max. values are 100% tested at TA = 25 °C.
Gen. Note: Exceeding the “Absolute Maximum Ratings” can damage the device.
Page 2
March 1999 TOKO, Inc.