TFM-1XX-XX-X-S-XX
NOTES:
1.
REVISION AG
REPRESENTS A CRITICAL DIMENSION.
2. MINIMUM PUSHOUT FORCE: 16 OZ FOR TERMINALS, 12 OZ FOR WELD TABS,
AND 8 OZ FOR LOCKING CLIPS.
OPTION
No OF POSITIONS
ALL POSITIONS AVAILABLE
-A: ALIGNMENT PIN (USE TFM-XX-S-01-A)
(NOT AVAILABLE WITH -WT OPTION)
(SEE FIG 5, SHEET 2)
DO NOT
SCALE FROM
THIS PRINT
3. MEASURED FROM BEND.
4. MAXIMUM TERMINAL BURR: .003 [.08].
5. MAXIMUM HEIGHT VARIATION BETWEEN ANY TWO PINS: .005 [.13].
6. DUE TO THE HIGH AMOUNT OF INSERTION FORCE NEEDED, THE -LC OPTION
IS NOT COMPATIBLE WITH AUTO PLACEMENT. SAMTEC RECOMMENDS
MANUAL PLACEMENT FOR ALL ASSEMBLIES WITH THE -LC OPTION.
-02 THRU -50
-LC: LOCKING CLIP (USE LC-05-TM)
(NOT AVAILABLE WITH -WT OPTION)
(SEE FIG 7, SHEET 3) (SEE NOTE 6)
-P: PICK AND PLACE PAD (USE PPP-15)
(SEE FIG 6, SHEET 2)
LEAD STYLE
-01: T-1R16-01-X-2
THROUGH HOLE
-02: T-1R16-01-X-2
SURFACE MOUNT
-03: T-1R16-10-X
THROUGH HOLE
(ONLY AVAILABLE ON -08 THRU -50 POSITIONS)
-K: POLYIMIDE FILM (SEE FIG 3, SHEET 2)
(USE K-DOT-.217-.313-.005)
-WT: WELD TABS (USE WT-25-07-T)
(SEE FIG 4, SHEET 2)
((No. OF POSITIONS x .050[1.27])
+ .125[3.18])REF
(AVAILABLE ON -02 THRU -30 POS ONLY)
(NOT AVAILABLE WITH -A OR -LC OPTIONS)
-TR: TAPE & REEL
PLATING SPECIFICATIONS
((No. OF POSITIONS x .050[1.27])
+ .025[.64])REF
(SEE SHEET 3, TAPE AND REEL VIEW)
-SN: SOLDER NAIL (USE WT-27-03)
-S: 30µ" SELECTIVE GOLD IN CONTACT AREA,
MATTE TIN ON TAIL
**
(NOT AVAILABLE WITH -A, -LC, OR
-WT OPTIONS) (SEE FIG 8, SHEET 3)
-F: 3µ" FLASH GOLD IN CONTACT AREA,
MATTE TIN ON TAIL
.100 2.54 REF
-G: 30µ" GOLD IN CONTACT AREA,
3µ" GOLD ON TAIL
BODY SPECIFICATION
-S: SINGLE ROW
(USE TFM-XX-S-XX-XX)
-L: 15µ" LIGHT GOLD IN CONTACT AREA,
MATTE TIN ON TAIL
.105 2.67 REF
.175 4.45 REF
.065 1.65
-H: 50µ" HEAVY GOLD IN CONTACT AREA,
3µ" GOLD ON TAIL
01
-T: MATTE TIN CONTACT AND TAIL
.083 2.11
.050 1.27 REF
** NOT TOOLED
((No. OF POSITIONS x .050[1.27])
- .050[1.27])
2
MAX SWAY
2
MAX SWAY
(EITHER DIRECTION)
(EITHER DIRECTION)
.018 0.46 REF
"A"
.1635 4.153 REF
.2200 5.588
"B" REF
REF
.010 0.25 REF
"A"
"A" .003
MAX SWAY
"C"±.003
.014 0.36 REF
2
2
MAX SWAY
(EITHER DIRECTION)
(EITHER DIRECTION)
((No. OF POSITIONS x .050[1.27])
- .050[1.27])
SECTION "A"-"A"
TABLE 1
POSITION
-02 THRU -29
-030 THRU -39
-40 THRU -50
COPLANARITY
.004 [.10]
.006 [.15]
IN-PROCESS
FIG 1
PROPRIETARY NOTE
UNLESS OTHERWISE SPECIFIED,
DIMENSIONS ARE IN INCHES.
TOLERANCES ARE:
(TFM-115-01-X-S-XX SHOWN)
THIS DOCUMENT CONTAINS INFORMATION
CONFIDENTIAL AND PROPRIETARY TO
.008 [.20]
SAMTEC, INC. AND SHALL NOT BE REPRODUCED
OR TRANSFERRED TO OTHER DOCUMENTS OR
DISCLOSED TO OTHERS OR USED FOR ANY
PURPOSE OTHER THAN THAT WHICH IT WAS
OBTAINED WITHOUT THE EXPRESSED WRITTEN
CONSENT OF SAMTEC, INC.
DECIMALS
ANGLES
2
.XX: .01 [.3]
520 PARK EAST BLVD, NEW ALBANY, IN 47150
PHONE: 812-944-6733 FAX: 812-948-5047
e-Mail info@SAMTEC.com code 55322
.XXX: .005 [.13]
TABLE 2
"A"
TFM-XX-S-01-XX .078 [1.98] .131 [3.33] .428 [10.87] .303 [7.70]
TFM-XX-S-01-XX N/A .131 [3.33] .428 [10.87] .231 [5.87]
TFM-XX-S-01-XX .111 [3.33] .139 [3.53] .645 [16.38] .356 [9.04]
.XXXX: .0020 [.051]
LEAD STYLE
BODY
"B"
"C"
"E"
SHEET SCALE: 1:0.4
MATERIAL:
DO NOT SCALE DRAWING
DESCRIPTION:
-01
-02
-03
INSULATOR: LCP, UL 94 V0, COLOR: BLACK
TERMINAL: PHOSPHOR BRONZE
.050 C.L. SINGLE ROW SHROUDED TERMINAL STRIP
DWG. NO.
TFM-1XX-XX-X-S-XX
8/21/2008 SHEET 1 OF 3
BY: D. SCHMELZ
F:\DWG\MISC\MKTG\TFM-1XX-XX-X-S-XX-MKT.SLDDRW