NOTES:
TFM-1XX-XX-XXX-D-XXX
REVISION FQ
1.
C
REPRESENTS A CRITICAL DIMENSION.
OPTION
C
2. MINIMUM PUSHOUT FORCE FOR CONTACTS, WELD TABS,
AND THREADED INSERTS: 12 OZ.
-A: ALIGNMENT PIN (USE TFM-XX-D-XX-A,
SEE TABLE 1) (SEE FIG 8, SHT 3)
No OF POSITIONS
3. MINIMUM LOCKING CLIP RETENTION: 8 OZS.
LEAD STYLE -01, -02, -03: -02 THRU -50 (ALL
POSITIONS AVAILABLE)
(NOT AVAILABLE FOR -RA OR -REX)
-LC: LOCKING CLIP (USE LC-05-TM)
(NOT AVAILABLE FOR -RA OR -REX)
(SEE FIG 10, SHT 3 & NOTES 3 & 11)
-P: PICK AND PLACE PAD (USE PPP-04)
(AVAILABLE IN ALL POSITIONS -05 THRU
-50 EXCEPT -05 WITH -WT)
4. MAXIMUM HEIGHT VARIATION BETWEEN ANY TWO PINS: .005[0.13]
5. MAXIMUM TERMINAL BURR: .003[0.08]
DO NOT
SCALE FROM
THIS PRINT
LEAD STYLES -11, -12, -13: (-05 THRU -50 MULTIPLES OF 5)
POSITIONS 12, 16, 17 ALSO AVAILABLE
6. COPLANARITY: .004[0.10] = POS 02 THRU 26
C
.006[0.15] = POS 27 THRU 50
LEAD STYLES -21, 22, 23: (-05 THRU -50 MULTIPLES OF 5)
POSITIONS 12 & 13 ALSO AVAILABLE
7. MEASURED FROM BEND.
8. DIMENSION CHANGED PER REVISION AD. CONTACT ENGINEERING
FOR INFORMATION.
LEAD STYLES 31, 32: 12 POSITION ALSO AVAILABLE
(NOT AVAILABLE FOR -RA OR -REX,
SEE FIG 7, SHT 3)
9. MEASURE FROM TIPS OF PIN.
10. NOTE DELETED.
LEAD STYLE
-RA: RIGHT ANGLE(AVAILABLE ONLY IN LEAD STYLE: -01
SEE FIG 5, SHT 2)
11. DUE TO THE HIGH AMOUNT OF INSERTION FORCE NEEDED,
THE –LC OPTION IS NOT COMPATIBLE WITH AUTO PLACEMENT. SAMTEC
RECOMMENDS MANUAL PLACEMENT FOR ALL ASSEMBLIES WITH THE
–LC OPTION.
THROUGH HOLE
-01, -03 (SEE FIG 1)
-11, -13 (SEE FIG 1)
-21,-23 (SEE FIG 1)
-31 (SEE FIG 1)
SURFACE MOUNT
-02 (SEE FIG 2)
-12 (SEE FIG 2)
-22 (SEE FIG 2)
-32 (SEE FIG 2)
-TR: TAPE AND REEL (SEE FIG 4, SHT 7(NOT AVAILABLE
WITH -DS OPTION OR THROUGH HOLE LEAD STYLE)
(SEE NOTES 14&15)
-SA: STAKED ALIGNMENT PIN (SEE FIG 9, SHT 3)
(ONLY AVAILABLE ON SURFACE MOUNT LEAD STYLE)
-K: POLYIMIDE FILM (SEE FIG 3, SHT 2)
(USE K-DOT-.217-.313-.005)
12. SIDES OF PLASTIC BODIES ON ALL LEAD STYLES EXCEPT THE -01, -02 & -03
WILL BE SOLID AND WITHOUT SIDE SLOTS.
PLATING SPECIFICATION
-S: 30µ" SELECTIVE GOLD ON CONTACT AREA,
13. NOTE DELETED.
14. NOT ALL PARTS FOLLOW EIA-481 ORIENTATION IN THE T&R POCKET.
15. -TR OPTION ORDERS INVOLVING PARTIAL REEL QUANTITIES MAY BE PACKAGED
ACCORDING TO THE SAMTEC PACKAGING EFFICIENCY STANDARDS (SPES) FOUND
ON WWW.SAMTEC.COM.
(NOT AVAILABLE FOR -RA OR -REX)
(ALL LEAD STYLES EXCEPT -21 AVAILABLE)
-WT: WELD TABS (USE WT-25-XX-T)
(AVAILABLE ON -01, -02 & -03 LEAD
STYLES ONLY) (SEE FIG 6, SHT 2)
MATTE TIN TAIL
-L: 15µ" SELECTIVE GOLD ON CONTACT AREA,
MATTE TIN TAIL
-F: 3µ" FLASH GOLD ON CONTACT AREA,
MATTE TIN TAIL
16. -FR OPTIONS WILL BE SHIPPED AT THE MAX QUANTITY PER REEL, BASED ON
OPTIONS SELECTED.
-H: 30µ" SELECTIVE GOLD ON CONTACT AREA,
3µ" FLASH GOLD ON TAIL
(MATES WITH SFSS/SFSD -SR & -DR ONLY)
(NOT AVAILABLE WITH -A, -LC,
(No OF POSITIONS x .050[1.27]) + .125[3.18] REF
-SM: 30µ" SELECTIVE GOLD ON CONTACT AREA,
MATTE TIN TAIL
(No OF POSITIONS x .050[1.27]) + .025[.64] REF
-RA, OR -SA OPTIONS)
-RE1: RIGHT ANGLE ELEVATED .062 PCB
(USE TFM-XX-D-01-RE, NOT AVAILABLE
WITHOUT -WT, AVAILABLE IN LEAD
STYLE -01 ONLY, -03 THRU -50 POS)
(MATES WITH SFSS/SFSD -SR & -DR ONLY)
(SEE FIG 11, SHT 4)
.110 2.79 REF
02
-LM: 15µ" SELECTIVE GOLD ON CONTACT AREA,
MATTE TIN TAIL
-FM: 3µ" FLASH GOLD ON CONTACT AREA,
MATTE TIN TAIL
.155 3.94
REF
-STL: 30µ" SELECTIVE GOLD ON CONTACT AREA,
TIN/LEAD (90/10 ±5%) TAIL
-RE2: RIGHT ANGLE ELEVATED .093 PCB
(USE TFM-XX-D-01-RE, NOT AVAILABLE
WITHOUT -WT, AVAILABLE IN LEAD
STYLE -01 ONLY, -03 THRU -50 POS)
(MATES WITH SFSS/SFSD -SR & -DR ONLY)
(SEE FIG 11, SHEET 4)
01
.050 1.27
BODY SPECIFICATION
.225 5.72
-D: DOUBLE ROW
.075 1.91
REF
REF
REF
C
.050 1.27
(No OF POSITIONS x .050[1.27]) - .050[1.27]
-SN: SOLDER NAIL FOR .062 BOARD
(TFM-XX-D-01-SN AND WT-27-01-T)
(SEE FIG12, SHT 3)
(EITHER DIRECTION)
2
MAX SWAY
"D" REF
(SEE TABLE 1,
SHT 7)
.018 0.46 REF
(ONLY AVAILABLE WITH -02 LEAD STYLE)
(NOT AVAILABLE WITH OPTIONS -A, -LC,
-RA, -SA, -WT, -RE1 OR -RE2)
.135 3.43 REF
2
MAX SWAY
"A"
(EITHER DIRECTION)
-SN2: SOLDER NAIL FOR .093 BOARD
(TFM-XX-D-01-SN AND WT-27-02-T)
(SEE FIG12, SHT 3)
.096 2.44
.1635 4.153
REF
"A" REF
(SEE TABLE 1,
SHT 7)
(SEE NOTE 8)
(ONLY AVAILABLE WITH -02 LEAD STYLE)
(NOT AVAILABLE WITH OPTIONS -A, -LC,
-RA, -SA, -WT, -RE1 OR -RE2)
-DS: DUAL SCREW DOWN FOR .062 BOARD
(SEE FIG 18, SHT 5)
SEE NOTE 12
(ONLY AVAILABLE WITH -01 & -02 LEAD STYLE)
(NOT AVAILABLE WITH OPTIONS -A, -LC, -P,
-RA, -TR, -SA, -K, -WT, -RE1, -RE2, -SN, -SN2)
(-01 LEAD STYLE USES TFM-XX-D-01-DSL
& T1-M2-4-VSFM-T, 02 LEAD STYLE USES
.010 0.25 REF
C
.014 0.36 REF
MAX SWAY
.050 1.27
MAX SWAY
"A"
C
2
"J" ± .003 [0.08]
(SEE TABLE 1, SHT 7)
2
(EITHER DIRECTION)
C
(EITHER DIRECTION)
TFM-XX-D-01-DSA & T1-M2-4-VSFM-T)
-FR: FULL REEL QTY. TAPE & REEL (NOT AVAILABLE WITH
-DS OPTION OR THROUGH HOLE LEAD STYLE)
(SEE NOTES 14 & 16)
SECTION "A"-"A"
(No OF POSITIONS x .050[1.27]) - .050[1.27]
C
PROPRIETARY NOTE
THIS DOCUMENT CONTAINS CONFIDENTIAL AND
PROPRIETARY INFORMATION AND ALL DESIGN,
UNLESS OTHERWISE SPECIFIED,
DIMENSIONS ARE IN INCHES.
*
*
TOLERANCES ARE:
DECIMALS
MANUFACTURING, REPRODUCTION, USE, PATENT RIGHTS
AND SALES RIGHTS ARE EXPRESSLY RESERVED BY SAMTEC,
INC. THIS DOCUMENT SHALL NOT BE DISCLOSED, IN WHOLE
OR PART, TO ANY UNAUTHORIZED PERSON OR ENTITY NOR
REPRODUCED, TRANSFERRED OR INCORPORATED IN ANY
OTHER PROJECT IN ANY MANNER WITHOUT THE EXPRESS
WRITTEN CONSENT OF SAMTEC, INC.
FIG 1
ANGLES
2
THROUGH HOLE
.XX: .01[0.3]
520 PARK EAST BLVD, NEW ALBANY, IN 47150
PHONE: 812-944-6733 FAX: 812-948-5047
e-Mail info@SAMTEC.com code 55322
.XXX: .005[0.13]
-01, -03, -11, -13, -21, -23, -31
.XXXX: .0020[0.051]
"C"±.003 [0.08]
(SEE TABLE 1, SHT 7)
C
SHEET SCALE: 2.5:1
MATERIAL:
DO NOT SCALE DRAWING
DESCRIPTION:
(APPLY FOR BOTH ROWS)
INSULATOR:
.050 X .050 TERMINAL STRIP
LCP, UL 94-VO
COLOR: BLACK
NO. TFM-1XX-XX-XXX-D-XXX
DWG.
TERMINAL: PHOSPHOR BRONZE
IN-PROCESS
SHEET 1 OF 7
F:\DWG\MISC\MKTG\TFM-1XX-XX-XXX-D-XXX-MKT.SLDDRW
BY:
garyp
11/5/2014