NOTES:
1.
TFM-1XX-XX-X-S-XX
REVISION Z
REPRESENTS A CRITICAL DIMENSION.
C
2. MINIMUM PUSHOUT FORCE TO BE 16 OZ FOR TERMINALS, 12 OZ FOR WELD TABS,
AND 8 OZ FOR LOCKING CLIPS.
OPTION
No OF POSITIONS
ALL POSITIONS AVAILABLE
-02 THRU -50
-A: ALIGNMENT PIN (USE TFM-XX-S-01-A)
(NOT AVAILABLE WITH -WT OPTION)
(SEE FIG. 5 SHEET 2)
3. MEASURED FROM BEND.
4. MAXIMUM TERMINAL BURR: .003 [.08]
5. MAXIMUM HEIGHT VARIATION BETWEEN ANY TWO PINS: .005 [.13]
6. DUE TO THE HIGH AMOUNT OF INSERTION FORCE NEEDED, THE -LC OPTION
IS NOT COMPATIBLE WITH AUTO PLACEMENT. SAMTEC RECOMMENDS
MANUAL PLACEMENT FOR ALL ASSEMBLIES WITH THE -LC OPTION.
Z
-LC: LOCKING CLIP (USE LC-05-TM)
(NOT AVAILABLE WITH -WT OPTION)
(SEE FIG. 7 SHEET 3) (SEE NOTE 6)
-P: PICK AND PLACE PAD (USE PPP-15)
(SEE FIG. 6 SHEET 2)
LEAD STYLE
-01: T-1R16-01-X-2
THROUGH HOLE
-02: T-1R16-01-X-2
SURFACE MOUNT
(NOT AVAILABLE -03, -04 & -05 POSITIONS)
-K: POLYIMIDE FILM (SEE FIG. 3 SHEET 2)
(USE K-500-300)
-03: T-1R16-10-X
-WT: WELD TABS (USE WT-25-07-T)
(SEE FIG. 4 SHEET 2)
*
THROUGH HOLE
(AVAILABLE ON -02 THRU -30 POS ONLY)
(NOT AVAILABLE WITH
PLATING SPECIFICATIONS
-A OR -LC OPTIONS)
C
-TR: TAPE & REEL
-S: 30µ" SELECTIVE GOLD IN CONTACT AREA,
MATTE TIN ON TAIL
(SEE SHEET 3, TAPE AND REEL VIEW)
-SN: SOLDER NAIL (USE WT-27-03)
(NOT AVAILABLE WITH -A, -LC, OR
-WT OPTIONS) (SEE FIG. 8 SHEET 3)
((No. OF POSITIONS x .050[1.27])
+ .125[3.18])REF
**
-F: 3µ" GOLD IN CONTACT AREA,
MATTE TIN ON TAIL
-P: 3µ" GOLD PALLADIUM NICKEL IN CONTACT
AREA, MATTE TIN ON TAIL
((No. OF POSITIONS x .050[1.27])
+ .025[.64])REF
BODY SPECIFICATION
-S: SINGLE ROW
(USE TFM-XX-S-XX-XX)
-L: 10µ" GOLD IN CONTACT AREA,
MATTE TIN ON TAIL
.100 2.54 REF
.105 2.67 REF
* NOT RELEASED FOR PRODUCTION
** NOT TOOLED
.065 1.65
01
C
.083 2.11
.050 1.27 REF
.175 4.45 REF
2 MAX TOE
(TYP)
.018 0.46
2
"A"
MAX SWAY
(TYP)
.1635 4.153 REF
"B" REF
.2200 5.588
C
.010 0.25 REF
"A"
"A"
C
"C"
2
MAX SWAY (TYP)
.014 0.36 REF
2
MAX TOE (TYP)
C
((No. OF POSITIONS x .050[1.27])
- .050[1.27])
C
SECTION "A"-"A"
TABLE 1
ALLOWABLE COPLANARITY
POSITIONS
-02 THRU -29
-030 THRU -39
-40 THRU -50
Z
IN-PROCESS
FIGURE 1
CPC
PROPRIETARY NOTE
THIS DOCUMENT CONTAINS INFORMATION
CONFIDENTIAL AND PROPRIETARY TO
SAMTEC, INC. AND SHALL NOT BE REPRODUCED
OR TRANSFERRED TO OTHER DOCUMENTS OR
DISCLOSED TO OTHERS OR USED FOR ANY
PURPOSE OTHER THAN THAT WHICH IT WAS
OBTAINED WITHOUT THE EXPRESSED WRITTEN
CONSENT OF SAMTEC, INC.
UNLESS OTHERWISE SPECIFIED,
DIMENSIONS ARE IN INCHES.
TOLERANCES ARE:
.004 MAX
.006 MAX
.008 MAX
(TFM-115-01-X-S-XX SHOWN)
FREQUENCY
THIS SHEET
DECIMALS
ANGLES
2
A
C1, C2
.XX: .01 [.3]
520 PARK EAST BLVD, NEW ALBANY, IN 47150
.XXX: .005 [.13]
PHONE: 812-944-6733
FAX: 812-948-5047
code 55322
.XXXX: .0020 [.051]
e-Mail info@SAMTEC.com
C3, C4, C5,
C6
B
TABLE 2
"A"
0.075 [1.91]
N/A
SHEET SCALE: 1:0.4
MATERIAL:
DO NOT SCALE DRAWING
DESCRIPTION:
LEAD STYLE
BODY
"B"
"C"
INSULATOR: LIQUID CRYSTAL POLYMER, COLOR: BLACK
TERMINAL: PHOSPHOR BRONZE
.050 C.L. SINGLE ROW SHROUDED TERMINAL STRIP
DWG. NO.
-01
-02
-03
TFM-XX-S-XX-XX
TFM-XX-S-XX-XX
TFM-XX-S-XX-XX
0.133 [3.38] 0.4285 [10.884]
0.133 [3.38] 0.4285 [10.884]
0.140 [3.56]
C
D
TFM-1XX-XX-X-S-XX
0.109 [2.77]
0.644 [16.36]
8/21/2008 SHEET 1 OF 3
BY: D. SCHMELZ
F:\DWG\MISC\MKTG\TFM-1XX-XX-X-S-XX-MKT.SLDDRW