SN65HVD251
www.ti.com
SLLS545C–NOVEMBER 2002–REVISED SEPTEMBER 2005
CAN TRANSCEIVER
Designed for operation in harsh environments, the
device features cross-wire, over-voltage and loss of
ground protection to ±36 V. Also featured are
over-temperature protection as well as -7 V to 12 V
common-mode range, and tolerance to transients of
±200 V. The transceiver interfaces the single-ended
CAN controller with the differential CAN bus found in
industrial, building automation, and automotive appli-
cations.
FEATURES
•
Drop-In Improved Replacement for the
PCA82C250 and PCA82C251
•
•
•
•
Bus-Fault Protection of ±36 V
Meets or Exceeds ISO 11898
Signaling Rates(1) Up to 1 Mbps
High Input Impedance Allows up to 120
SN65HVD251 Nodes on a Bus
•
•
•
•
•
Bus Pin ESD Protection Exceeds 14 kV HBM
Unpowered Node Does Not Disturb the Bus
Low-Current Standby Mode — 200 µA Typical
Thermal Shutdown Protection
Glitch-Free Power-Up and Power-Down Bus
Protection For Hot-Plugging
Rs, pin 8, selects one of three different modes of
operation: high-speed, slope control, or low-power
mode. The high-speed mode of operation is selected
by connecting pin 8 to ground, allowing the transmit-
ter output transistors to switch as fast as possible
with no limitation on the rise and fall slope. The rise
and fall slope can be adjusted by connecting a
resistor to ground at pin 8; the slope is proportional to
the pin's output current. Slope control with an external
resistor value of 10 kΩ gives ~ 15 V/us slew rate; 100
kΩ gives ~ 2 V/us slew rate.
•
(1)
DeviceNet Vendor ID # 806
The signaling rate of a line is the number of voltage transitions
that are made per second expressed in bps (bits per second).
If a high logic level is applied to the Rs pin 8, the
device enters a low-current standby mode where the
driver is switched off and the receiver remains active.
The local protocol controller returns the device to the
normal mode when it transmits to the bus.
APPLICATIONS
•
CAN Data Buses
•
Industrial Automation
– DeviceNet™ Data Buses
– Smart Distributed Systems (SDS™)
SAE J1939 Standard Data Bus Interface
NMEA 2000 Standard Data Bus Interface
ISO 11783 Standard Data Bus Interface
The SN65HVD251 may be used in CAN,
DeviceNet™ or SDS™ applications with the Texas
Instruments' TMS320F241 and TMS320F243 DSPs
with CAN 2.0B controllers.
•
•
•
function diagram
(positive logic)
DESCRIPTION
3
5
The SN65HVD251 is intended for use in applications
employing the Controller Area Network (CAN) serial
communication physical layer in accordance with the
ISO 11898 Standard. The SN65HVD251 provides
differential transmit capability to the bus and differen-
tial receive capability to a CAN controller at speeds
up to 1 megabits per second (Mbps).
V
V
1
2
ref
8
7
Rs
D
CC
GND
CANH
CANL
Vref
1
8
D
Vcc
R
3
4
6
5
R
S
7
6
CANH
CANL
4
R
ORDERING INFORMATION
PART NUMBER
SN65HVD251D
SN65HVD251DR
SN65HVD251P
PACKAGE
8-pin SOIC (Tube)
8-pin SOIC (Tape & Reel)
8-pin DIP
MARKED AS
VP251
VP251
65HVD251
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas
Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
DeviceNet is a trademark of Allen-Bradley.
SDS is a trademark of Honeywell.
PRODUCTION DATA information is current as of publication date.
Copyright © 2002–2005, Texas Instruments Incorporated
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
5秒后页面跳转
解析光耦仿真器：升级光耦合器技术的必要性
英伟达新一代Blackwell GPU过热问题致交付延迟
国产厂商思特威CMOS图像传感器芯片单月出货超1亿颗，技术创新引领行业发展
台积电5nm和3nm产能利用率达100%，半导体行业景气度持续攀升
微信公众号
抖音公众号
浙公网安备 33010502006866号 浙ICP备10014259号-119
营业执照ICP证
数据手册
如果您发现信息不准确，
