Pl tronics, Inc.
.
19013 36th Ave. W, Suite H Lynnwood, WA 98036 USA
Manufacturer of High Quality Frequency Control Products
SM7745D CMOS Series
CMOS with Enable/ Disable, 3rd Overtone Crystal Used
4 Pad 7 x 5mm Leadless Surface Mount Ceramic Clock Oscillator
–
70.00 MHz 170.00 MHz
Low Jitter
Consult factory for higher frequencies
Standard Specifications
Overall Frequency Stability
SM7745D: ± 50 PPM, SM7744D: ± 25 PPM, SM7720D: ± 20 PPM over Operating Temp. Range
°
Operating Temperature Range 0 to +70 C is standard, but can be extended to - 40 to +85°C for certain frequencies
Supply Voltage (Vcc)
Symmetry (Duty Cycle)
5.0, 3.3, and 2.5 volts available, .01 µF bypass cap recommended, consult factory for 1.8 volts
40/60 to 60/40% is standard, but 45/55% at 50% of Vcc is also available (see Waveform 1)
Logic Levels
Jitter
Logic “1” 90% of Vcc MIN; Logic “0” 10% of Vcc MAX
1 pS RMS maximum, from 12 kHz to 20 MHz from carrier
Output Load
Enable/Disable Option (E/D)
Standard load is 15 pF (typ. 1 ASIC) maximum, see Test Circuit 2 (consult factory for heavier loads)
Output enabled when Pin #1 is open or at Logic “1”; Output disabled when Pin #1 is at Logic “0”.
See Website for Supply Current (Icc) and Rise and Fall Times
Part Numbering Guide
Portions of the part number that appear after the frequency may not be marked on part (C of C provided)
SM77 45 D V - 70.0M - 30 - XXX (Internal Code or blank)
Packaging
Tray or
16mm tape
8mm pitch
Non-Std Output Load
Blank = 15 pF max, 30 = 30 pF max
Model
Frequency in MHz
Frequency Stability
45 = ± 50 PPM
44 = ± 25 PPM
20 = ± 20 PPM
Special Specifications (choose all that apply)
°
Y: Std Specs (5.0V ± 10%, 0 to +70 C, 40/60% Symmetry)
°
E: Extended Operating Temperature Range (- 40 to +85 C)
S: 45/55% Symmetry at 50% of Vcc
V: Supply Voltage of 3.3 volts ± 10%
W: Supply Voltage of 2.5 volts ± 5%
X: Supply Voltage of 1.8 volts ± 5% (Consult factory)
Consult factory for available frequencies and specs. Not all options available for all frequencies. A special part number may be assigned.
Frequency Stability is inclusive of frequency shifts due to calibration, temperature, supply voltage, shock, vibration and load
Mechanical:
not to scale
inches (mm)
Solder Pads
Due to part size and factory abilities, part marking may vary from lot to lot and may contain our part number or an internal code.
0.200 (5.08)
0.276 (7.0 ± .15)
PIN SIGNAL
0.004 (0.10)
0.050 (1.27)
1
2
3
4
E/D
3
2
4
3
2
4
1
GND
OUT
Vcc
0.087 (2.2)
0.079 (2.0)
.01 m F
bypass
capacitor
1
0.055
(1.4)
0.024
(0.60)
0.075 (1.9)
MAX
0.200 (5.08)
0.055 0.145
(1.4)
(3.68)
Sept 2004
(425) 776 -1880, Fax: (425) 776-2760, ple-sales@pletronics.com, www.pletronics.com
8
Pl tronics, Inc.