SID11x2K
ꢂꢄꢃ
ꢏ
ꢈꢍꢎꢉ
ꢂꢁꢉꢉ
ꢂISꢅ
ꢋꢊꢌ
SꢈꢅꢑꢐꢚꢄIꢑꢄꢖIꢐ
DꢃꢐꢃꢄꢐIꢅꢀ
ꢔꢅꢅꢐSꢐꢑꢒꢗ
ꢄꢈꢒꢑꢁꢃ ꢗꢖꢆꢗ
ꢂꢄꢄ
ꢇꢃꢂꢃꢇ
SꢈIꢊꢐꢃꢑ
ꢒSSD
ꢁꢈ
ꢊꢋꢌxꢇꢍꢎꢏ
Sꢅ
ꢐꢑꢒꢀSꢄꢃIꢂꢃꢑ
ꢓꢔIDIꢑꢃꢄꢐIꢅꢀꢒꢇꢕ
ꢐꢑꢒꢀSꢄꢃIꢂꢃꢑ
ꢓꢔIDIꢑꢃꢄꢐIꢅꢀꢒꢇꢕ
ꢂISꢅ
ꢁꢇ
ꢁꢀD
ꢄꢅꢑꢃ ꢇꢅꢁIꢄ
Sꢖꢗꢗꢇꢘ
ꢆꢅꢀIꢐꢅꢑIꢀꢁ
ꢒꢖꢉIꢇIꢒꢑꢘ
ꢗꢅꢙꢃꢑ SꢖꢗꢗꢇIꢃS
ꢄꢅꢑꢃ ꢇꢅꢁIꢄ
ꢄꢅꢆ
Sꢖꢗꢗꢇꢘ
ꢆꢅꢀIꢐꢅꢑIꢀꢁ
ꢒꢖꢉIꢇIꢒꢑꢘ
Iꢀ
ꢈꢁꢉꢊ
ꢗꢅꢙꢃꢑ SꢖꢗꢗꢇIꢃS
ꢂꢃꢃ ꢄꢅꢀꢐꢑꢅꢇ
ꢂꢃꢃ
ꢀꢁꢂꢃꢄ5ꢅꢂ0ꢆꢇꢇ1ꢄ
Figure 3. Functional Block Diagram.
VISO Pin (Pin 14):
This pin is the input for the secondary-side positive supply voltage.
Pin Functional Description
VCC Pin (Pin 1):
This pin is the primary-side supply voltage connection.
COM Pin (Pin 15):
This pin provides the secondary-side reference potential.
GND Pin (Pin 3-6):
This pin is the connection for the primary-side ground potential.
All primary-side voltages refer to the pin.
GL Pin (Pin 16):
This pin is the driver output – sinking current (turn-off).
IN Pin (Pin 7):
This pin is the input for the logic command signal.
SO Pin (Pin 8):
This pin is the output for the logic fault signal (open drain).
NC Pin (Pin 9):
ꢄꢂꢂ 1
1ꢎ ꢆꢏ
This pin must be un-connected. Minimum PCB pad size for soldering
is required.
1ꢌ ꢂꢋꢍ
1ꢊ ꢄISꢋ
1ꢈ ꢆꢉ
12 ꢄꢆꢇꢇ
11 ꢄꢂꢅ
1ꢃ ꢄꢅꢅ
ꢀ ꢁꢂ
VEE Pin (Pin 10):
Common (IGBT emitter/MOSFET source) output supply voltage.
ꢆꢁD ꢈꢐꢎ
VCE Pin (Pin 11):
This pin is the desaturation monitoring voltage input connection.
Iꢁ ꢑ
Sꢋ ꢒ
VGXX Pin (Pin 12):
This pin is the bootstrap and charge pump supply voltage source.
GH Pin (Pin 13):
This pin is the driver output – sourcing current (turn-on) connection.
ꢀꢁꢂꢃꢄꢅ8ꢂ0ꢅ1ꢅ15
Figure 4.
Pin Configuration.
2
Rev. G 05/18
www.power.com