35W Single Output Switching Power Supply
SCP-35 series
■ Features :
%Universal AC input/Full range
%Protections: Short circuit / Overload / Over voltage / Battery
polarity protections (by fuse)
%Built-in temperature compensation function
%Output voltage detection signal
%Cooling by free air convection
%LED indicator for power on
%No load power consumption <0.75W
%100% full load burn-in test
SPECIFICATION
%2 years warranty
MODEL
SCP-35-12
SCP-35-24
DC VOLTAGE
13.8V
2.6A
27.6V
1.4A
RATED CURRENT
CURRENT RANGE
PEAK 5S
0 ~ 2.6A
0 ~ 1.4A
1.7A
Note.6 3.1A
35.9W
RATED POWER
38.6W
200mVp-p
+15,-5%
1.0%
RIPPLE & NOISE (max.) Note.2 120mVp-p
VOLTAGE ADJ. RANGE
VOLTAGE TOLERANCE Note.3 2.0%
LINE REGULATION Note.4 1.0%
LOAD REGULATION Note.5 2.0%
OUTPUT
+15,-5%
1.0%
1.0%
SETUP, RISE TIME
500ms, 30ms/230VAC
1200ms, 30ms/115VAC at full load
HOLD UP TIME (Typ.)
VOLTAGE RANGE
50ms/230VAC
85 ~ 264VAC
47 ~ 63Hz
16ms/115VAC at full load
120 ~ 370VDC
0.5 A/230VAC
FREQUENCY RANGE
EFFICIENCY (Typ.)
83%
86%
INPUT
AC CURRENT (Typ.)
INRUSH CURRENT (Typ.)
LEAKAGE CURRENT
TEMP. COMPENSATION
0.75A/115VAC
COLD START 45A
<2mA / 240VAC
By NTC (not provide with the power supply)
FUNCTION
OUTPUT VOLTAGE SENSOR L=output voltage +0.2 ~ 0.7V(AC OK); L=0V(AC Fail)
1.7 ~ 2.3A rated output power
3.1 ~ 4.2A rated output power
OVERLOAD
Protection type : Hiccup mode, recovers automatically after fault condition is removed
PROTECTION
33.1 ~ 38.5V
16.6 ~ 19.3V
OVER VOLTAGE
Protection type : Shut down o/p voltage, re-power on to recover
-20 ~ +60℃ (Refer to output load derating curve)
20 ~ 90% RH non-condensing
-40 ~ +85℃, 10 ~ 95% RH
WORKING TEMP.
WORKING HUMIDITY
STORAGE TEMP., HUMIDITY
TEMP. COEFFICIENT
VIBRATION
ENVIRONMENT
0.05% /℃ (0 ~ 45℃)
10 ~ 500Hz, 2G 10min./1cycle, period for 60min. each along X, Y, Z axes
UL60950-1, CB(IEC60950-1),CCC GB4943 approved
SAFETY STANDARDS
WITHSTAND VOLTAGE
ISOLATION RESISTANCE
I/P-O/P:3KVAC I/P-FG:1.5KVAC O/P-FG:0.5KVAC
SAFETY &
I/P-O/P, I/P-FG, O/P-FG:100M Ohms / 500VDC / 25℃/ 70% RH
Compliance to EN55022 (CISPR22) Class B, EN61000-3-2,3
Compliance to EN61000-4-2, 3, 4, 5, 6, 8,11, ENV50204, EN55024, EN61000-6-1, light industry level, criteria A
523.3Khrs min. MIL-HDBK-217F (25℃)
EMC
(Note 6)
EMC EMISSION
EMC IMMUNITY
MTBF
DIMENSION
PACKING
OTHERS
NOTE
99*97*36mm (L*W*H)
0.37Kg; 45pcs/17.7Kg/1CUFT
1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25℃ of ambient temperature.
2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.
3. Tolerance : includes set up tolerance, line regulation and load regulation.
4. Line regulation is measured from low line to high line at rated load.
5. Load regulation is measured from 0% to 100% rated load.
6. 33% Duty cycle maximum within every 15 seconds. Average output power should not exceed the rated power.
7. The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meets
EMC directives.
(As available on http://www.meanwell.com)
File Name:SCP-35-SPEC 2011-05-24