RESISTORSCAPACITORSCOILSDELAY LINES
SURGE RESISTORS, 1/8W to 15W, 2KV to 25KV
RCD PR2
10K 5%
Term.”W”
is Pb-free
PR SERIES
and RoHS
compliant;
“Q” is Sn-Pb
RoHS
Cost effective high-voltage surge resistors to 200 joules
Available on RCD’s exclusive SWIFTTM program
Molded surface mount version available (PRM series)
Excellent Low Cost Replacement for Composition Resistors
Series PR pulse resistors withstand higher energy pulses than conven-
tional film & wirewound types, without the performance disadvantages
of carbon comp resistors. The heavy duty construction features a high
thermal conductivity core and coating, enabling improved stability and
environmental performance. Series PR satisy a wide variety of pulse
applications including lightning, snubber, in-rush current, capacitor
charge, etc. RoHS (Sn) or Mil-spec (Sn-Pb) termination finish available.
OPTIONS
Opt. ER: Group A Screening per MIL-R-39008 RCR
Opt. F: Flameproof coating
Opt. B: Increased power (see Specifications table)
Opt. X: Non-inductive (see Performance Char. table)
Custom marking, cut & form, burn-in, etc.
→ D ←
←
H
→
← L →
d
↓
Inch [mm]
↑
SPECIFICATIONS
Max.
Max.
Wattage Rating
RCD
Type
Resistance
Range5
Continuous Peak Pulse
L (Body Length)
D6 (Body Dia.)
d±.004 [.1] H4 (min)
Voltage1,5,8 Voltage2,5,8
Standard Option B
PR1/8
PR1/4
PR1/2
PR1
1/8W
1/4W
1/2W
1W
1/2W
1W
150V
250V
350V
500V
750V
800V
1000V
2KV
3.5KV
5KV
0.1W-2K
0.1W-10K
0.1W-24K
0.1W-100K
0.1W-200K .875±.062 [22.2±1.6]
0.1W-220K 1.05±.062 [26.7± 1.6]
.145±.025 [3.69±.64]
.240±.032 [6.1±.8]
.375±.040 [9.2±1]
.600±.040 [15.2±1]
.062±.015 [1.6±.38]
.085±.025 [2.16±.64]
.156±.025 [3.96±.64]
.225±.032 [5.72±.8]
.312±.040 [7.92±1]
.350±.040 [8.89±1]
.350±.040 [8.89±1]
.018 [.46]
.022 [.56]
.028 [.7]
.031 [.8]3
.039 [1]3
.039 [1]
1.0 [25.4]
1.0 [25.4]
1.25 [32]
2W
4W
10KV
15KV
18KV
25KV
1.25 [32]
PR2
2W
5W
1.375 [35]7
1.375 [35]
1.375 [35]
PR5
5W
10W
15W
PR10
10W
0.1W-510K
1.72±.062[43.7±1.6]
.039 [1]
1 Max voltage = √(PxR), not to exceed value listed. 2 Pulse voltage & energy capability is dependent on res.value, waveform, repetition rate, & environmental conditions (refer to R-42 for derating factors). 3 .040” (1mm) lead
dia. is available on PR1 (specify PR1-18), .032” [.8mm] lead dia. is available on PR2 (specify PR2-20) 4Lead length is for bulk packaging, taped parts may be shorter (consult taping dimensions). 5 Expanded range avail.
6Allow .024” [.6mm] additonal for Opt. X or values <1W 7 Specify Opt. 56 for 1.5” [38.1] min. lead length, Opt. 70 for 2” [50.8] lead length 8Multiply by 0.7 on Opt.X parts.
SURGE CAPABILITY
1000
100
10
PR10
PR5
PR2
PR1/2
PR1
1
PR1/4
PR1/8
0.1 0.25 0.5 .75
1
2.5
5
7.5 10 25 50 75 100 250 500 750 1K 2.5K 5K 7.5K 10K 25K 50K 75K 100K
Resistance Value (ohms)
PERFORMANCE CHARACTERISTICS, Typ.
APPLICATION NOTE
Use chart above to select model to meet desired surge level. Pulse not to exceed
peak V & j ratings (derate 30% for Opt.X), and average power during repetitive
pulses nte rated W. A safety factor of 30% typ. is recommended for infrequent
pulses, 50% typ. for repetitive pulses (refer to Note R42 for derating factors at-
tributable to pulse width, rep. rate, temp., altitude, humidity). Verify by evaluating
under worst-case conditions. Depending on specifics, PR series can often satisfy
the surge requirements of UL-217, -268, -294, -497, -508, -913, -943, -991, -1459,
-1971, ANSI/IEEE C62.41, CCITT (Rec. K17), Bellcore TR-NWT-001089 & TR-
TSY-000057, CSA C22.2-225, IEC 664, IEC 801.5, IEEE587, Can.Doc. CS-03,
FCC Part 68., etc. Consult factory for assistance.
PR1/8-PR2: 1.25%/°C >70°C,
Derating, Wattage & Voltage
PR5-PR10 & Opt. B: 0.8%/°C >25°C
0.2uH PR1/8X-PR1/2X,0.3uH PR1X-PR2X,
Max.Induc*: Opt. X≤50W
0.7uH PR5X-PR10X
0.37uH PR1/8X-PR1/2X, 0.6uH PR1X-
Max.Induc*: Opt. X>50W
PR2X, 1.4uH PR5X-PR10X
Short-time Overload
Temperature Cycling
TCR (20 & 50ppm avail.)
Moisture Resistance
Shock and Vibration
Effect of Soldering
Voltage Coefficient
Load Life
±0.5%
±0.5%
±100ppm/°C(<0.2W=200ppm)
P/N DESIGNATION:
RCD Type
PR1/2
- 102 - K
T
W
±1%
±0.2%
Options: X, S, F, ER, B (leave blank if std)
±0.2%
Resis. Code 1% tol: 3 signif. figures & multiplier,
±0.005%/V
e.g. R100=0.1W, 1R00=1W, 10R0=10W, 1000=100W, 1001=1K.
2%-10%: 2 signif.fig. & multiplier (R10=0.1W, 1R0=1W, 100=10W, 102=1K)
Tolerance: J=5% (standard), F=1%, G=2%, K=10%
±0.5% Std, ±1% Opt.B
-55 to +150°C, +275°C avail.
Operating Temp Range
Packaging: B = bulk, T = Tape & Reel
Dielectric Strength (1KV avail.) 500V (PR1/8 & PR1/4 =300V)
Optional TC: 20 =20ppm, 50= 50ppm (leave blank if standard)
* specify Opt.75 for induc levels 50% that of Opt.X, or Opt.76 for 33% that of Opt.X
Termination: W= RoHS (std), Q= Tin/Lead (leave blank if either is acceptable)
-
-
-
-
RCD Components Inc, 520 E.Industrial Park Dr, Manchester, NH, USA 03109 rcdcomponents.com Tel: 603 669 0054 Fax: 603 669 5455 Email:sales@rcdcomponents.com
FA029K
Sale of this product is in accordance with GF-061. Specifications subject to change without notice.
73
5秒后页面跳转
英伟达新AI芯片Rubin或提前半年亮相
苹果iPhone 17将全系采用三星/LG显示LTPO OLED面板
三星深化印度制造布局，供应链本地化进程加速
芯擎科技“星辰一号”自动驾驶芯片点亮成功，2025年量产在即
微信公众号
抖音公众号
浙公网安备 33010502006866号 浙ICP备10014259号-119
营业执照ICP证
数据手册
如果您发现信息不准确，
