CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS
Radial Lead Type, Long Life Assurance
LV series
High voltage (to 100V), Low ESR, High ripple current.
Long life of 3000 hours at 105°C.
Radial lead type:
Lead free flow soldering condition correspondence.
Compliant to the RoHS directive (2002/95/EC).
High Temperature
High Voltage Long Life
LF
LX
LV
Specifications
Item
Performance Characteristics
Category Temperature Range
Rated Voltage Range
Rated Capacitance Range
Capacitance Tolerance
Tangent of loss angle (tan δ)
–55 to +105°C
16 to 100V
6.8 to 470µF
±20% at 120Hz, 20°C
Less than or equal to the specified value 120Hz, 20°C
at
(
1)
Less than or equal to the specified value 100kHz, 20°C
at
ESR
Leakage Current ( 2)
Less than or equal to the specified value. After 2 minutes' application of rated voltage at 20°C
Temperature Characteristics
(Max.Impedance Ratio)
Z+105°C / Z+20°C
Z–55°C / Z+20°C
1.25
1.25
(100kHz)
Capacitance change
(
)
)
Within ± 20% of the initial capacitance value
3
The specifications listed at right shall be met when the
capacitors are restored to 20°C after the rated voltage is
applied for 3000 hours at 105°C.
tan δ
150% or less than the initial specified value
150% or less than the initial specified value
Less than or equal to the initial specified value
Endurance
(
1)
ESR
Leakage current ( 2)
Capacitance change
(
Within ± 20% of the initial capacitance value
3
The specifications listed at right shall be met when the
capacitors are restored to 20°C after the rated voltage is
applied for 1000 hours at 60°C, 90% RH.
Damp Heat
tan δ
150% or less than the initial specified value
150% or less than the initial specified value
Less than or equal to the initial specified value
(
1)
ESR
(Steady State)
Leakage current ( 2)
After soldering the capacitor under the soldering conditions
prescribed here as preheat at 150 to 200°C for 60 to 180 seconds
and peak temperature at 265°C for 10 seconds or less, the
capacitor shall meet the specifications listed at right, provided that
its temperature profile is measured at both of terminal ends facing
the soldering side.
Capacitance change
(
)
Within ± 10% of the initial capacitance value
3
tan δ
130% or less than the initial specified value
130% or less than the initial specified value
Less than or equal to the initial specified value
Resistance to
Soldering Heat
(
1)
ESR
Leakage current ( 2)
Marking
Navy blue print on the case top
1 ESR should be measured at both of the terminal ends closest to the capacitor body.
2 Conditioning : If any doubt arises, measure the leakage current after the voltage treatment of applying DC rated voltage continuously to the capacitor for 120
minutes at 105°C.
3 Initial value : The value before test of examination of resistance to soldering.
Type numbering system (Example : 35V 82 F)
µ
Dimensions
Tinned lead Wire
Resin coated Case
Capacitance
1
2
3
4
5
6
7
8
9
10 11 12
Voltage(V:35V)
P L V 1 V 8 2 0 M
D L 1
Size code
Configuration
Capacitance tolerance (±20%)
Rated capacitance (82µF)
Rated voltage (35V)
Series name
φd
Series
Lot. No.
+0.5MAX.
15MIN
4MIN
L
Type
(mm)
13L
10.0
12.5
5.0
Size
φD
L
P
φd
φ8 × 9L φ8 × 12L φ10
×
Voltage
8.0
8.5
3.5
0.6
8.0
11.5
3.5
V
16
C
20
D
25
E
35
V
50
H
63
J
80 100
Code
K
2A
0.6
0.6
Please refer to page 20 about the end seal configulation.
Dimension table in next page.
CAT.8100A-1