CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS
Chip Type, LongLife Assurance
PCS
Load life of 5000 hours at 105°C.
SMD type : Lead free reflow soldering condition at
260°C peak correspondence.
Compliant to the RoHS directive (2011/65/EU).
AEC-Q200 compliant. Please contact us for details.
Long Life
PCF
PCS
Specifications
Item
Performance Characteristics
Category Temperature Range
Rated Voltage Range
Rated Capacitance Range
Capacitance Tolerance
Tangent of loss angle (tan δ)
–55 to +105°C
4 to 16V
22 to 560µF
20% at 120Hz, 20°C
Less than or equal to the specified value 120Hz, 20°C
at
(
1)
ESR
Less than or equal to the specified value 100kHz, 20°C
at
Leakage Current ( 2)
Less than or equal to the specified value . After 2 minutes' application of rated voltage at 20°C
Temperature Characteristics
(Max.Impedance Ratio)
Z+105°C / Z+20°C 1.25
Z–55°C / Z+20°C 1.25
(100kHz)
Within 20% of the initial capacitance value ( 3)
150% or less than the initial specified value
150% or less than the initial specified value
Less than or equal to the initial specified value
Capacitance change
The specifications listed at right shall be met when the
capacitors are restored to 20°C after the rated voltage is
applied for 5000 hours at 105°C.
tan δ
Endurance
(
1)
ESR
Leakage current ( 2)
Within 20% of the initial capacitance value ( 3)
150% or less than the initial specified value
150% or less than the initial specified value
Less than or equal to the initial specified value
Capacitance change
The specifications listed at right shall be met when the
capacitors are restored to 20°C after the rated voltage is
applied for 1000 hours at 60°C, 90% RH.
Damp Heat
tan δ
(
1)
ESR
(Steady State)
Leakage current ( 2)
After soldering the capacitor under the soldering conditions
prescribed here, the capacitor shall meet the specifications listed at
right.
Pre-heating shall be done at 150 to 200°C and for 60 to 180 sec.
The duration for over +230°C temperature at capacitor surface shall
not exceed 60 seconds.
Within 10% of the initial capacitance value ( 3)
130% or less than the initial specified value
130% or less than the initial specified value
Less than or equal to the initial specified value
Capacitance change
tan δ
(
1)
ESR
Leakage current ( 2)
Resistance to
Soldering Heat
In case peak temperature is 250°C or less, reflow soldering shall be
two times maximum.
In case peak temperature is 260°C or less, reflow soldering shall be
once.
Measurement for solder temperature profile shall be made at the
capacitor top and the terminal.
Marking
Navy blue print on the case top
1 ESR should be measured at both of the terminal ends closest where the terminals protrude through the plastic platform.
2 Conditioning : If any doubt arises, measure the leakage current after the voltage treatment of applying DC rated voltage continuously to the capacitor for 120
minutes at 105°C.
3 Initial value : The value before test of examination of resistance to soldering.
Type numbering system (Example : 6.3V 220µF)
Dimensions
Positive
1
2
3
4
5
6
7
8
9 10 11 12 13 14
Plastic platform
0.3 MAX.
Capacitance
Lot No.
C
0.2
P C S 0 J 2 2 1 M C L 1 G S
Taping code
Size code
Configuration
Capacitance tolerance ( 20ꢀ%
+0.1
-0.4
L
Rated capacitance
(
220µF
%
%
Voltage ( j:6.3v)
Series
H
Negative
Rated voltage
(
6.3V
Series name
Type
(mm)
7L
8.0
φ5 × 6L φ6.3 × 6L φ8
×
Size
φD
L
5.0
5.9
6.0
5.3
5.3
1.6
6.3
5.9
7.3
6.6
6.6
2.1
6.9
9.0
8.3
8.3
3.2
A
B
Voltage
V
Frequency coefficient of rated ripple current
0 Frequency0/ 120Hz 1kHz 10kHz 100kHz or more
C
4
g
6.3
10
16
C
E
Code
j
A
0.5 to 0.8 0.5 to 0.8 0.8 to 1.1
Coefficient
0.05
0.30
0.70
1.00
H
Dimension table in next page.
47
CAT.8100H